View W83L517DW83L517D-F_4282056.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

W83L517D/W83L517D-F
Winbond LPC I/O for Notebook W83L517D/ W83L517D-F
Date: May 23, 2005. Version: 1.0
-1-
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Table of Contents1. 2. 3. 4. GENERAL DESCRIPTION .............................................................................................................. 6 FEATURES...................................................................................................................................... 7 PIN CONFIGURATION FOR W83L517D........................................................................................ 9 PIN DESCRIPTION ....................................................................................................................... 10 4.1 4.2 4.3 4.4 4.5 4.6 5. 6. LPC Interface....................................................................................................................... 10 FDC Interface ...................................................................................................................... 11 Multi-Mode Parallel Port ...................................................................................................... 12 Serial Port Interface and Infrared Port ................................................................................ 17 KBC and FLASH ROM Interface ......................................................................................... 19 POWER PINS...................................................................................................................... 20
LPC (LOW PIN COUNT) INTERFACE.......................................................................................... 21 FDC FUNCTIONAL DESCRIPTION.............................................................................................. 21 6.1 W83L517D FDC .................................................................................................................. 21
6.1.1 6.1.2 6.1.3 6.1.4 6.1.5 6.1.6 6.1.7 AT interface ..........................................................................................................................21 FIFO (Data) ..........................................................................................................................21 Data Separator .....................................................................................................................22 Write Precompensation ........................................................................................................23 Perpendicular Recording Mode ............................................................................................23 FDC Core .............................................................................................................................23 FDC Commands...................................................................................................................23 Status Register A (SA Register) (Read base address + 0)...................................................34 Status Register B (SB Register) (Read base address + 1)...................................................36 Digital Output Register (DO Register) (Write base address + 2) ..........................................38 Tape Drive Register (TD Register) (Read base address + 3)...............................................38 Main Status Register (MS Register) (Read base address + 4).............................................39 Data Rate Register (DR Register) (Write base address + 4) ................................................39 FIFO Register (R/W base address + 5) ................................................................................41 Digital Input Register (DI Register) (Read base address + 7)...............................................43 Configuration Control Register (CC Register) (Write base address + 7) ..............................44
6.2
Register Descriptions .......................................................................................................... 34
6.2.1 6.2.2 6.2.3 6.2.4 6.2.5 6.2.6 6.2.7 6.2.8 6.2.9
7.
UART PORT .................................................................................................................................. 45 7.1 7.2 Universal Asynchronous Receiver/Transmitter (UART A) .................................................. 45 Register Address................................................................................................................. 45
7.2.1 7.2.2 7.2.3 7.2.4 7.2.5 7.2.6 UART Control Register (UCR) (Read/Write) ........................................................................45 UART Status Register (USR) (Read/Write) ..........................................................................48 Handshake Control Register (HCR) (Read/Write) ................................................................49 Handshake Status Register (HSR) (Read/Write)..................................................................50 UART FIFO Control Register (UFR) (Write only)..................................................................51 Interrupt Status Register (ISR) (Read only) ..........................................................................52
-2-
W83L517D/W83L517D-F
7.2.7 7.2.8 7.2.9 Interrupt Control Register (ICR) (Read/Write) ......................................................................53 Programmable Baud Generator (BLL/BHL) (Read/Write).....................................................54 User-defined Register (UDR) (Read/Write) ..........................................................................54
8.
INFRARED (IR) PORT .................................................................................................................. 55 8.1 8.2 IR Register Description ....................................................................................................... 55 Set0-Legacy/Advanced IR Control and Status Registers ................................................... 57
8.2.1 8.2.2 8.2.3 8.2.4 8.2.5 8.2.6 8.2.7 Set0.Reg0 - Receiver/Transmitter Buffer Registers (RBR/TBR) (Read/Write) .....................57 Set0.Reg1 - Interrupt Control Register (ICR)........................................................................57 Set0.Reg2 - Interrupt Status Register/IR FIFO Control Register (ISR/UFR) ........................59 Set0.Reg3 - IR Control Register/Set Select Register (UCR/SSR): .......................................62 Set0.Reg4 - Handshake Control Register (HCR) .................................................................63 Set0.Reg5 - IR Status Register (USR) .................................................................................65 Set0.Reg6 - Reserved ..........................................................................................................66 Set1.Reg0~1 - Baud Rate Divisor Latch (BLL/BHL) .............................................................67 Set1.Reg 2~7 .......................................................................................................................68 Reg0, 1 - Advanced Baud Rate Divisor Latch (ABLL/ABHL) ................................................68 Reg2 - Advanced IR Control Register 1 (ADCR1) ................................................................68 Reg3 - Sets Select Register (SSR).......................................................................................69 Reg4 - Advanced IR Control Register 2 (ADCR2) ................................................................70 Reg6 - Transmitter FIFO Depth (TXFDTH) (Read Only) ......................................................72 Reg7 - Receiver FIFO Depth (RXFDTH) (Read Only)..........................................................72 Reg0 - Advanced IR ID (AUID).............................................................................................72 Reg1 - Mapped IR Control Register (MP_UCR) ...................................................................73 Reg2 - Mapped IR FIFO Control Register (MP_UFR) ..........................................................73 Reg3 - Sets Select Register (SSR).......................................................................................73 Set4.Reg0, 1 - Timer Value Register (TMRL/TMRH) ...........................................................74 Set4.Reg2 - Infrared Mode Select (IR_MSL) ........................................................................74 Set4.Reg3 - Set Select Register (SSR) ................................................................................74 Set4.Reg4, 5 - Transmitter Frame Length (TFRLL/TFRLH) .................................................75 Set4.Reg6, 7 - Receiver Frame Length (RFRLL/RFRLH) ....................................................75 Set5.Reg0, 1 - Flow Control Baud Rate Divisor Latch Register (FCDLL/ FCDHL) ...............76 Set5.Reg2 - Flow Control Mode Operation (FC_MD) ...........................................................76 Set5.Reg3 - Sets Select Register (SSR) ..............................................................................76 Set5.Reg4 - Infrared Configure Register 1 (IRCFG1)...........................................................77 Set5.Reg5 - Frame Status FIFO Register (FS_FO) .............................................................77
8.3
Set1 - Legacy Baud Rate Divisor Register.......................................................................... 67
8.3.1 8.3.2
8.4
Set2 - Interrupt Status or IR FIFO Control Register (ISR/UFR) .......................................... 68
8.4.1 8.4.2 8.4.3 8.4.4 8.4.5 8.4.6
8.5
Set3 - Version ID and Mapped Control Registers............................................................... 72
8.5.1 8.5.2 8.5.3 8.5.4
8.6
Set4 - TX/RX/Timer counter registers and IR control registers. ......................................... 73
8.6.1 8.6.2 8.6.3 8.6.4 8.6.5
8.7
Set 5 - Flow control and IR control and Frame Status FIFO registers................................ 75
8.7.1 8.7.2 8.7.3 8.7.4 8.7.5
-3-
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
8.7.6 Set5.Reg6, 7 - Receiver Frame Length FIFO (RFLFL/RFLFH) or Lost Frame Number (LST_NU) ...........................................................................................................................................78
8.8
Set6 - IR Physical Layer Control Registers......................................................................... 79
8.8.1 8.8.2 8.8.3 8.8.4 8.8.5 8.8.6 8.8.7 8.8.8 Set6.Reg0 - Infrared Configure Register 2 (IR_CFG2).........................................................79 Set6.Reg1 - MIR (1.152M/0.576M bps) Pulse Width............................................................80 Set6.Reg2 - SIR Pulse Width ...............................................................................................80 Set6.Reg3 - Set Select Register...........................................................................................81 Set6.Reg4 - High Speed Infrared Beginning Flag Number (HIR_FNU) ...............................81 Set6.Reg5 - Winbond infrared ID Register 1........................................................................82 Set6.Reg6 - Winbond infrared ID Register 2........................................................................82 Set6.Reg7 - High Speed infrared ID Select Register ...........................................................82 Set7.Reg0 - Remote Infrared Receiver Control (RIR_RXC) .................................................83 Set7.Reg1 - Remote Infrared Transmitter Control (RIR_TXC) .............................................85 Set7.Reg2 - Remote Infrared Config Register (RIR_CFG)...................................................86 Set7.Reg3 - Sets Select Register (SSR) ..............................................................................87 Set7.Reg4 - Infrared Module (Front End) Select 1 (IRM_SL1) .............................................87 Set7.Reg5 - Infrared Module (Front End) Select 2 (IRM_SL2) .............................................88 Set7.Reg6 - Infrared Module (Front End) Select 3 (IRM_SL3) .............................................88 Set7.Reg7 - Infrared Module Control Register (IRM_CR) ....................................................89
8.9
Set7 - Remote control and IR module selection registers................................................... 83
8.9.1 8.9.2 8.9.3 8.9.4 8.9.5 8.9.6 8.9.7 8.9.8
9.
PARALLEL PORT......................................................................................................................... 90 9.1 9.2 Printer Interface Logic ......................................................................................................... 90 Enhanced Parallel Port (EPP) ............................................................................................. 91
9.2.1 9.2.2 9.2.3 9.2.4 9.2.5 9.2.6 9.2.7 9.2.8 Data Swapper.......................................................................................................................92 Printer Status Buffer .............................................................................................................92 Printer Control Latch and Printer Control Swapper...............................................................92 EPP Address Port ................................................................................................................93 EPP Data Port 0-3 ................................................................................................................94 Bit Map of Parallel Port and EPP Registers..........................................................................94 EPP Pin Descriptions ...........................................................................................................95 EPP Operation .....................................................................................................................95 ECP Register and Mode Definitions .....................................................................................96 Data and ecpAFifo Port ........................................................................................................97 Device Status Register (DSR) ..............................................................................................97 Device Control Register (DCR).............................................................................................98 cFifo (Parallel Port Data FIFO) Mode = 010 .........................................................................98 ecpDFifo (ECP Data FIFO) Mode = 011...............................................................................99 tFifo (Test FIFO Mode) Mode = 110 .....................................................................................99 cnfgA (Configuration Register A) Mode = 111 ......................................................................99 cnfgB (Configuration Register B) Mode = 111 ......................................................................99 ecr (Extended Control Register) Mode = all........................................................................100
9.3
Extended Capabilities Parallel (ECP) Port .......................................................................... 96
9.3.1 9.3.2 9.3.3 9.3.4 9.3.5 9.3.6 9.3.7 9.3.8 9.3.9 9.3.10
-4-
W83L517D/W83L517D-F
9.3.11 9.3.12 9.3.13 9.3.14 9.3.15 9.3.16 Bit Map of ECP Port Registers ...........................................................................................101 ECP Pin Descriptions .........................................................................................................102 ECP Operation ...................................................................................................................102 FIFO Operation ..................................................................................................................103 DMA Transfers ...................................................................................................................103 Programmed I/O (NON-DMA) Mode...................................................................................103
9.4 9.5
Extension FDD Mode (EXTFDD) ...................................................................................... 104 Extension 2FDD Mode (EXT2FDD) .................................................................................. 104
10. GENERAL PURPOSE I/O ........................................................................................................... 104 11. ACPI REGISTERS FEATURES .................................................................................................. 107 12. CONFIGURATION REGISTER ................................................................................................... 107 12.1 Plug and Play Configuration.............................................................................................. 107 12.2 Compatible PnP................................................................................................................. 108
12.2.1 12.2.2 12.2.3 12.3.1 12.3.2 12.3.3 12.3.4 Extended Function Registers..............................................................................................108 Extended Functions Enable Registers (EFERs) .................................................................109 Extended Function Index Registers (EFIRs), Extended Function Data Registers(EFDRs) 109 Enter the extended function mode......................................................................................109 Configurate the configuration registers...............................................................................109 Exit the extended function mode ........................................................................................109 Software programming example.........................................................................................110
12.3 Configuration Sequence.................................................................................................... 109
12.4 Chip (Global) Control Register .......................................................................................... 111 12.5 Logical Device 0 (FDC) ..................................................................................................... 116 12.6 Logical Device 1 (Parallel Port) ......................................................................................... 119 12.7 Logical Device 2 (UART A) ............................................................................................... 120 12.8 Logical Device 6 (FIR)....................................................................................................... 121 12.9 Logical Device 7 ( GPIO Port 1) ........................................................................................ 122 12.10 Logical Device 8 ( GPIO Port 2) ........................................................................................ 124 12.11 Logical Device 9 (GPIO Port 3 ~ GPIO Port 5 ) ................................................................ 124 12.12 Logical Device A (ACPI).................................................................................................... 125 13. ORDERING INSTRUCTION........................................................................................................ 128 14. HOW TO READ THE TOP MARKING ........................................................................................ 129 15. PACKAGE DIMENSIONS............................................................................................................ 130 16. RECOMMENDED CIRCUIT ........................................................................................................ 131 17. REVISION HISTORY................................................................................................................... 133
-5-
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
1. GENERAL DESCRIPTION
The W83L517D is evolving product from Winbond's most popular I/O family. They feature a whole new interface, namely LPC (Low Pin Count) interface, which will be supported in the new generation chip-set. This interface as its name suggests is to provide an economical implementation of I/O's interface with lower pin count and still maintains equivalent performance as its ISA interface counterpart. Approximately 40 pin counts are saved in LPC I/O comparing to ISA implementation. With this additional freedom, we can implement more devices on a single chip as demonstrated in W83L517D's integration of Flash ROM Interface. It is fully transparent in terms of software which means no BIOS or device driver update is needed except chip-specific configuration. The disk drive adapter functions of W83L517D include a floppy disk drive controller compatible with the industry standard 82077/ 765, data separator, write pre-compensation circuit, decode logic, data rate selection, clock generator, drive interface control logic, and interrupt and DMA logic. The wide range of functions integrated onto the W83L517D greatly reduces the number of components required for interfacing with floppy disk drives. The W83L517D supports four 360K, 720K, 1.2M, 1.44M, or 2.88M disk drives and data transfer rates of 250 Kb/s, 300 Kb/s, 500 Kb/s,1 Mb/s, and 2 Mb/s. The W83L517D provides one high-speed serial communication ports (UARTs), one of which supports serial Infrared communication. The UART includes a 16-byte send/receive FIFO, a programmable baud rate generator, complete modem control capability, and a processor interrupt system. The UART provides legacy speed with baud rate up to 115.2k bps and also advanced speed with baud rates of 230k, 460k, or 921k bps which support higher speed modems. In addition, the W83L517D provides IR functions: IrDA 1.0 (SIR for 1.152K bps) and IrDA 1.1 (MIR for 1.152M bps or FIR for 4M bps), TV remote IR, (Consumer IR, supporting NEC, RC-5, extended RC-5, and RECS-80 protocols). The W83L517D supports one PC-compatible printer port (SPP), Bi-directional Printer port (BPP) and also Enhanced Parallel Port (EPP) and Extended Capabilities Port (ECP). Through the printer port interface pins, also available are: Extension FDD Mode and Extension 2FDD Mode allowing one or two external floppy disk drives to be connected. The configuration registers support mode selection, function enable/disable, and power down function selection. Furthermore, the configurable PnP features are compatible with the plug-and-play feature TM demand of Windows 95/98 , which makes system resource allocation more efficient than ever. The W83L517D provides a set of flexible I/O control functions to the system designer through a set of General Purpose I/O ports. These GPIO ports may serve as simple I/O or may be individually configured to provide a predefined alternate function. General Purpose Port 1 is designed to be functional even in power down mode (VCC is off). The W83L517D is made to fully comply with Microsoft(c) PC98 and PC99 Hardware Design Guide, and meet the requirements of ACPI. The W83L517D provides two important interfaces -- "Flash ROM interface and ISA keyboard controller interface". The Flash ROM interface can support up to 4M legacy flash ROM. The ISA KBC interface can supports legacy KBC such as Mitsubishi H8 and Intel 8xC51.
-6-
W83L517D/W83L517D-F
2. FEATURES
General
* * * * * * * * * * * * * * * * * * * * * * * * * Meet LPC Spec. 1.01 Support LDRQ#(LPC DMA), SERIRQ (serial IRQ) Include all the features of Winbond I/O W83877ATF Compliant with Microsoft PC98/PC99 Hardware Design Guide Support DPM (Device Power Management), ACPI Support hardware power down mode Support printer port/floppy hardware auto-detect and auto-swap Programmable configuration settings Single 24 or 48 MHz clock input Compatible with IBM PC AT disk drive systems Variable write pre-compensation with track selectable capability Support vertical recording format DMA enable logic 16-byte data FIFOs Support floppy disk drives and tape drives Detects all overrun and underrun conditions Built-in address mark detection circuit to simplify the read electronics FDD anti-virus functions with software write protect and FDD write enable signal (write data signal was forced to be inactive) Support up to four 3.5-inch or 5.25-inch floppy disk drives Completely compatible with industry standard 82077 360K/720K/1.2M/1.44M/2.88M format; 250K, 300K, 500K, 1M, 2M bps data transfer rate Support 3-mode FDD, and its Win95/98 driver High-speed 16550 compatible UARTs with 16-byte send/receive FIFOs MIDI compatible Fully programmable serial-interface characteristics: --- 5, 6, 7 or 8-bit characters --- Even, odd or no parity bit generation/detection --- 1, 1.5 or 2 stop bits generation
FDC
UART
-7-
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
* Internal diagnostic capabilities: --- Loop-back controls for communications link fault isolation --- Break, parity, overrun, framing error simulation * * * * * Programmable baud generator allows division of 1.8461 MHz and 24 MHz by 1 to (216-1) Maximum baud rate up to 921k bps for 14.769 MHz and 1.5M bps for 24 MhzInfrared Support IrDA version 1.0 SIR protocol with maximum baud rate up to 115.2K bps Support SHARP ASK-IR protocol with maximum baud rate up to 57,600 bps Support IrDA version 1.1 MIR (1.152M bps) and FIR (4M bps) protocol --- Single DMA channel for transmitter or receiver --- 32-byte FIFO is supported in both FIR TX/RX transmission --- 8-byte status FIFO is supported to store received frame status (such as overrun, CRC error, etc.) * * * * * * * * * * * * * * * Support auto-config SIR and FIR Support full Customer IR Support driver for MicrosoftTM Windows 95TM and Windows 98TM (Memphis TM) Compatible with IBMTM parallel port Support PS/2 compatible bi-directional parallel port Support Enhanced Parallel Port (EPP) - Compatible with IEEE 1284 specification Support Extended Capabilities Port (ECP) - Compatible with IEEE 1284 specification Extension FDD mode supports disk drive B; and Extension 2FDD mode supports disk drives A and B through parallel port Enhanced printer port back-drive current protection Support up to 4M flash ROM Support Legacy ISA keyboard controller 38 programmable general purpose I/O ports General purpose I/O ports can serve as simple I/O ports, watch dog timer output, power LED output, infrared I/O pins, suspend LED output, Beep output Functional in power down mode 100-pin LQFP
Parallel Port
Flash ROM Interface Keyboard Controller Interface General Purpose I/O Ports
Package
-8-
W83L517D/W83L517D-F
3. PIN CONFIGURATION FOR W83L517D
XA6/GP43 XA7/GP44 XA8/GP45 XA9/GP46 XA10/GP47 XA11/GP50 XA12/GP51 XA13/GP52 XA14/GP53 GND XA15/GP54 XA16/GP55 XA17/GP56 XA18/GP57 VCC HEAD# RDATA# WP# TRAK0# WE# WD# STEP# DIR# MOA# DSKCHG#
77 777766666 54 321098765 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 11 12345678901
XA5/GP42 XA4/GP41 XA3/GP40 XA2/GP27 XA1/GP26 XA0/GP15 ROMCS#/GP14/PENROM# MEMW#/GP13 MEMR#/GP12 XD7/GP37 XD6/GP36 XD5/GP35 XD4/GP34 XD3/GP33 GND XD2/GP32 XD1/GP31 XD0/GP30 IOW#/GP25 IOR#/GP24 IRQ12IN/GP23 IRQ1IN/GP22 MCCS#/GP21 KBCS#/GP20/PENKB# VCC3V 66666555555555 43210987654321 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26
W83L517D
1111 11 11222222 2345 67 89012345
IRSEL0_IRRXH IRTX IRRX RIA# DCDA# SOUTA/PEN48 SINA DTRA#/PNPCSv# RTSA#/HEFRAS DSR# VCC CTSA# STB# AFD# ERR# GND INIT# SLIN# PD7 PD6 PD5 PD4 PD3 PD2 PD1
RTCCS#/GP11 CLKIN PME# LRESET# PDCTL# GND SERIRQ PCICLK LDRQ# LAD0 VCC3V LAD1 LAD2 LAD3 LFRAME# PRT_NFDD# SLCT PE BUSY ACK# PD0
P8 0C S# /G P1 0
DSA# INDEX# DRVDEN0
-9-
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
4. PIN DESCRIPTION
Note: Please refer to Section 13.2 DC CHARACTERISTICS for details.
I/O8t I/O12t I/O12tp3 I/OD12t I/O24t OUT12t OUT12tp3 OD12 OD24 INcs INt INtd INts INtsp3
- TTL level bi-directional pin with 8 mA source-sink capability - TTL level bi-directional pin with 12 mA source-sink capability - 3.3V TTL level bi-directional pin with 12 mA source-sink capability - TTL level bi-directional pin open drain output with 12 mA sink capability - TTL level bi-directional pin with 24 mA source-sink capability - TTL level output pin with 12 mA source-sink capability - 3.3V TTL level output pin with 12 mA source-sink capability - Open-drain output pin with 12 mA sink capability - Open-drain output pin with 24 mA sink capability - CMOS level Schmitt-trigger input pin - TTL level input pin - TTL level input pin with internal pull down resistor - TTL level Schmitt-trigger input pin - 3.3V TTL level Schmitt-trigger input pin
4.1
LPC Interface
PIN I/O FUNCTION
SYMBOL
CLKIN PME# PCICLK LDRQ# SERIRQ LAD[0:3] LFRAME# LRESET# PDCTL#
6 7 12 13 11 14, 16-18 19 8 9
INt OD12 INtsp3 O12tp3 I/OD12t I/O12tp3 INtsp3 INtsp3 INtsp3
System clock input. According to the input frequency 24MHz or 48MHz, it is selectable through register. Default is 24MHz input. Generated PME event. PCI clock input. Encoded DMA Request signal. Serial IRQ input/Output. These signal lines communicate address, control, and data information over the LPC bus between a host and a peripheral. Indicates start of a new cycle or termination of a broken cycle. Reset signal. It can connect to PCIRST# signal on the host. Hardware power down input pin for chip power down. Programmable control by registers.
- 10 -
W83L517D/W83L517D-F
4.2 FDC Interface
PIN I/O FUNCTION
SYMBOL
DRVDEN0
3
OD24
Drive Density Select bit 0. This Schmitt-triggered input from the disk drive is active low when the head is positioned over the beginning of a track marked by an index hole. This input pin is pulled up internally by a 1 K resistor. The resistor can be disabled by bit 7 of L0CRF0 (FIPURDWN). Drive Select A. When set to 0, this pin enables disk drive A. This is an open drain output. Diskette change. This signal is active low at power on and whenever the diskette is removed. This input pin is pulled up internally by a 1 K resistor. The resistor can be disabled by bit 7 of L0-CRF0 (FIPURDWN). Motor A On. When set to 0, this pin enables disk drive 0. This is an open drain output. Direction of the head step motor. An open drain output. Logic 1 = outward motion Logic 0 = inward motion Step output pulses. This active low open drain output produces a pulse to move the head to another track. Write data. This logic low open drain writes pre-compensation serial data to the selected FDD. An open drain output. Write enable. An open drain output. Track 0. This Schmitt-triggered input from the disk drive is active low when the head is positioned over the outermost track. This input pin is pulled up internally by a 1 K resistor. The resistor can be disabled by bit 7 of L0-CRF0 (FIPURDWN). Write protected. This active low Schmitt input from the disk drive indicates that the diskette is write-protected. This input pin is pulled up internally by a 1 K resistor. The resistor can be disabled by bit 7 of L0-CRF0 (FIPURDWN). The read data input signal from the FDD. This input pin is pulled up internally by a 1 K resistor. The resistor can be disabled by bit 7 of L0-CRF0 (FIPURDWN). Head select. This open drain output determines which disk drive head is active. Logic 1 = side 0 Logic 0 = side 1
INDEX#
2
INcs
DSA#
1
OD24
DSKCHG#
100
INcs
MOA#
99
OD24
DIR#
98
OD24
STEP# WD# WE# TRAK0#
97 96 95 94
OD24 OD24 OD24 INcs
WP#
93
INcs
RDATA#
92
INcs
HEAD#
91
OD24
- 11 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
4.3 Multi-Mode Parallel Port
SYMBOL PIN I/O FUNCTION
The following pins have alternate functions, which are controlled by CR28 and L3-CRF0.
PRT_NFDD#
20
INtsp3
PRT_NFDD# is the printer Not Floppy signal. It indicated the connected device as Printer or Floppy Disk on printer port. If the default function(Printer mode) is used, it must connect to low level. PRINTER MODE: An active high input on this pin indicates that the printer is selected. This pin is pulled high internally. Refer to the description of the parallel port for definition of this pin in ECP and EPP mode.
SLCT
21
INt
(WE2#)
OD12
EXTENSION FDD MODE: WE2# This pin is for Extension FDD B; its function is the same as the WE# pin of FDC.
OD12
EXTENSION 2FDD MODE: WE2# This pin is for Extension FDD A and B; its function is the same as the WE# pin of FDC.
PE
22
INt
PRINTER MODE: An active high input on this pin indicates that the printer has detected the end of the paper. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(WD2#)
OD12
EXTENSION FDD MODE: WD2# This pin is for Extension FDD B; its function is the same as the WD# pin of FDC.
OD12
EXTENSION 2FDD MODE: WD2# This pin is for Extension FDD A and B; its function is the same as the WD# pin of FDC.
- 12 -
W83L517D/W83L517D-F
Multi-Mode Parallel Port, continued
SYMBOL
PIN
I/O
FUNCTION
BUSY
23
INt
PRINTER MODE: An active high input indicates that the printer is not ready to receive data. This pin is pulled high internally. Refer to the description of the parallel port for definition of this pin in ECP and EPP mode.
(MOB2#)
OD12
EXTENSION FDD MODE: MOB2# This pin is for Extension FDD B; its function is the same as the MOB# pin of FDC.
OD12
EXTENSION 2FDD MODE: MOB2# This pin is for Extension FDD A and B; its function is the same as the MOB# pin of FDC.
ACK#
24
INt
PRINTER MODE: ACK# An active low input on this pin indicates that the printer has received data and is ready to accept more data. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(DSB#)
OD12
EXTENSION FDD MODE: DSB2# This pin is for the Extension FDD B; its functions is the same as the DSB# pin of FDC.
OD12
EXTENSION 2FDD MODE: DSB2# This pin is for Extension FDD A and B; its function is the same as the DSB# pin of FDC.
PD0
25
I/O12t
PRINTER MODE: PD0 Parallel port data bus bit 0. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(INDEX2#)
INt
EXTENSION FDD MODE: INDEX2# This pin is for Extension FDD B; its function is the same as the INDEX# pin of FDC. It is pulled high internally.
INt
EXTENSION 2FDD MODE: INDEX2# This pin is for Extension FDD A and B; its function is the same as the INDEX# pin of FDC. It is pulled high internally.
- 13 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Multi-Mode Parallel Port, continued
SYMBOL
PIN
I/O
FUNCTION
PD1
26
I/O12t
PRINTER MODE: PD1 Parallel port data bus bit 1. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(TRAK02#)
INt
EXTENSION FDD MODE: TRAK02# This pin is for Extension FDD B; its function is the same as the TRAK0# pin of FDC. It is pulled high internally. EXTENSION. 2FDD MODE: TRAK02# This pin is for Extension FDD A and B; its function is the same as the TRAK0# pin of FDC. It is pulled high internally.
INt
PD2
27
I/O12t
PRINTER MODE: PD2 Parallel port data bus bit 2. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(WP2#)
INt
EXTENSION FDD MODE: WP2# This pin is for Extension FDD B; its function is the same as the WP# pin of FDC. It is pulled high internally.
INt
EXTENSION. 2FDD MODE: WP2# This pin is for Extension FDD A and B; its function is the same as the WP# pin of FDC. It is pulled high internally.
PD3
28
I/O12t
PRINTER MODE: PD3 Parallel port data bus bit 3. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(RDATA2#)
INt
EXTENSION FDD MODE: RDATA2# This pin is for Extension FDD B; its function is the same as the RDATA# pin of FDC. It is pulled high internally. EXTENSION 2FDD MODE: RDATA2# This pin is for Extension FDD A and B; its function is the same as the RDATA# pin of FDC. It is pulled high internally.
INt
- 14 -
W83L517D/W83L517D-F
Multi-Mode Parallel Port, continued
SYMBOL
PIN
I/O
FUNCTION
PD4
29
I/O12t
PRINTER MODE: PD4 Parallel port data bus bit 4. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(DSKCHG2#)
INt
EXTENSION FDD MODE: DSKCHG2# This pin is for Extension FDD B; the function of this pin is the same as the DSKCHG# pin of FDC. It is pulled high internally. EXTENSION 2FDD MODE: DSKCHG2# This pin is for Extension FDD A and B; this function of this pin is the same as the DSKCHG# pin of FDC. It is pulled high internally.
Int
PD5
30
I/O12t
PRINTER MODE: PD5 Parallel port data bus bit 5. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
PD6 31 I/OD12t
EXTENSION FDD MODE: This pin is a tri-state output. EXTENSION 2FDD MODE: This pin is a tri-state output. PRINTER MODE: PD6 Parallel port data bus bit 6. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode. EXTENSION FDD MODE: This pin is a tri-state output. EXTENSION. 2FDD MODE: MOA2# This pin is for Extension FDD A; its function is the same as the MOA# pin of FDC.
(MOA2#)
OD12
PD7
32
I/OD12t
PRINTER MODE: PD7 Parallel port data bus bit 7. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(DSA2#)
OD12
EXTENSION FDD MODE: This pin is a tri-state output. EXTENSION 2FDD MODE: DSA2# This pin is for Extension FDD A; its function is the same as the DSA# pin of FDC.
- 15 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Multi-Mode Parallel Port, continued
SYMBOL
PIN
I/O
FUNCTION
SLIN#
33
OD12
PRINTER MODE: SLIN# Output line for detection of printer selection. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(STEP2#)
OD12
EXTENSION FDD MODE: STEP2# This pin is for Extension FDD B; its function is the same as the STEP# pin of FDC. EXTENSION 2FDD MODE: STEP2# This pin is for Extension FDD A and B; its function is the same as the STEP# pin of FDC.
OD12
INIT#
34
OD12
PRINTER MODE: INIT# Output line for the printer initialization. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(DIR2#)
OD12
EXTENSION FDD MODE: DIR2# This pin is for Extension FDD B; its function is the same as the DIR# pin of FDC. EXTENSION 2FDD MODE: DIR2# This pin is for Extension FDD A and B; its function is the same as the DIR# pin of FDC.
OD12
ERR#
36
INt
PRINTER MODE: ERR# An active low input on this pin indicates that the printer has encountered an error condition. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(HEAD2#)
OD12
EXTENSION FDD MODE: HEAD2# This pin is for Extension FDD B; its function is the same as the HEAD# pin of FDC. EXTENSION 2FDD MODE: HEAD2# This pin is for Extension FDD A and B; its function is the same as the HEAD# pin of FDC.
OD12
- 16 -
W83L517D/W83L517D-F
Multi-Mode Parallel Port, continued
SYMBOL
PIN
I/O
FUNCTION
AFD#
37
OD12
PRINTER MODE: AFD# An active low output from this pin causes the printer to auto feed a line after a line is printed. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
(DRVDEN0)
OD12
EXTENSION FDD MODE: DRVDEN0 This pin is for Extension FDD B; its function is the same as the DRVDEN0 pin of FDC. EXTENSION 2FDD MODE: DRVDEN0 This pin is for Extension FDD A and B; its function is the same as the DRVDEN0 pin of FDC.
OD12
STB#
38
OD12
PRINTER MODE: STB# An active low output is used to latch the parallel data into the printer. This pin is pulled high internally. Refer to the description of the parallel port for the definition of this pin in ECP and EPP mode.
-
EXTENSION FDD MODE: This pin is a tri-state output. EXTENSION 2FDD MODE: This pin is a tri-state output.
4.4
Serial Port Interface and Infrared Port
SYMBOL PIN I/O FUNCTION
CTSA#
39
Int
Clear To Send. It is the modem control input. The function of these pins can be tested by reading bit 4 of the handshake status register.
DSRA#
41
Int
Data Set Ready. An active low signal indicates the modem or data set is ready to establish a communication link and transfer data to the UART. UART A Request To Send. An active low signal informs the modem or data set that the controller is ready to send data. During power-on reset, this pin is pulled down internally and is defined as HEFRAS and configuration port's address is slected to 2Eh, which provides the power-on value for CRXX bit X (HEFRAS). A 4.7 k resistor is recommended if intends to pull up and selects 4EH as configuration I/O ports address)
RTSA# (HEFRAS)
42
I/O8t
- 17 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Serial Port Interface, continued
SYMBOL
PIN
I/O
FUNCTION
DTRA#
43
I/O8t
UART A Data Terminal Ready. An active low signal informs the modem or data set that the controller is ready to communicate. During power-on reset, this pin is pulled down internally and is defined as PNPCSV#, which provides the power-on value for CR24 bit 0 (PNPCSV#). A 4.7 k is recommended if intends to pull up. (clear the default value of FDC, UARTs, and PRT)
(PNPCSV#)
SINA SOUTA
44 45
INt I/O8
Serial Input. It is used to receive serial data through the communication link. UART A Serial Output. It is used to transmit serial data out to the communication link. During power-on reset, this pin is pulled down internally and is defined as PEN48 and the clock input (Pin 6) should be 48MHz, which provides the power-on value for CRxx bit x (EN48). A 4.7 k resistor is recommended if intends to pull up and 24MHz input is slected. Data Carrier Detect. An active low signal indicates the modem or data set has detected a data carrier. Ring Indicator. An active low signal indicates that a ring signal is being received from the modem or data set. Alternate Function W83L517D only) Input: Infrared Receiver input.(For
(PEN48)
INt
DCDA# RIA# IRRX IRTX IRSEL0_ IRRXH
46 47 48 49 50
INt INt INts OUT12t I/O12t
Alternate Function Output: Infrared Transmitter Output. (For W83L517D only) After reset, this pin is Infrared Control Signal 0 , this signal is output and selecte FIR or SIR mode for IR module . This pin can be set as IRRXH , the signal is high speed infrared receiver input . (For W83L517D only)
- 18 -
W83L517D/W83L517D-F
4.5 KBC and FLASH ROM Interface
PIN I/O FUNCTION
SYMBOL
P80CS# (GP10) (PLED) RTCCS# (GP11) (WDTO) KBCS# (GP20) (PENKB#) 52 OD12 I/O12 INt 5 I/OD12 4 I/OD12
Decoded I/O write asserted and the address 0x80h to output selected signal. General purpose I/O PORT 1 , Programmable Power LED. Decoded the address 0x70h and 0x71h to output selected signal . General purpose I/O PORT 1 , Programmable watch dog timer. Decode the address 60h and 64h to output selected signal. Enable by PENKB# signal with Low-level during power-on setting. General purpose I/O PORT 2 , During power-on reset, this pin is pulled down internally and is defined as PENKB# and all the K/B interface will be active, which provides the power on value for CR24 bit 7. A 4.7k resistor is recommended if intends to pull up and disable K/B functions. Decode the address 62h and 66h to output selected signal Enable by PENKB# signal with Lo-level during power-on setting. I/O12 Int General purpose I/O PORT 2 , Parallel Interrupt Requested Input 1. This interrupt request is used for specific K/B functions. General purpose I/O PORT 2 , Parallel Interrupt Requested Input 12. This interrupt request is used for specific K/B functions. General purpose I/O PORT 2 , I/O Read. IOR# is the command to an ISA I/O slave device that the slave may drive data on to the ISA data bus (XD[0:7]). General purpose I/O PORT 2 ,. I/O Write. IOW# is the command to an ISA I/O slave device that the slave may latch data from the ISA data bus (XD[0:7]). General purpose I/O PORT 2 , XData BUS. XD[0:7] provide the 8-bit data path for KBC and ROM devices residing on the ISA Bus. General purpose I/O PORT 3 ,
MCCS# 53 (GP21) IRQ1IN 54 (GP22) IRQ12IN 55 (GP23) IOR# 56 (GP24) IOW# 57 (GP25) XD[0:7] (GP30GP37) 58-60 62-66
OD12
I/O12 Int I/O12 O12t I/O12t O12t I/O12t I/O12t I/O12t
- 19 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
KBC and FLASH ROM Interface, continued
SYMBOL
PIN
I/O
FUNCTION
MEMR# (GP12) MEMW# (GP13) ROMCS# (GP14) (PENROM#)
67
O12t I/O12t O12t I/O12t OD12 I/OD12 INt
Flash ROM interface Memory Read Enable General purpose I/O PORT 1 , Flash ROM interface Memory Write Enable General purpose I/O PORT 1 , Flash ROM interface Chip Select General purpose I/O PORT 1 , During power-on reset , this pin is pulled down internally and is defined as PENROM# and decoded memory address of BIOS to output selected signal, which provides the power on value for CR24 bit 1. A 4.7k is recommended if intends to pull up and disable BIOS ROM function . Flash ROM interface Address 0. General purpose I/O PORT 1 , Flash ROM interface Address 1. General purpose I/O PORT 2 , Flash ROM interface Address 2. General purpose I/O PORT 2 , Flash ROM interface Address [3:10]. General purpose I/O PORT 4 , Flash ROM interface Address [11:18]. General purpose I/O PORT 5 ,
68
69
XA0 (GP15) XA1 (GP26) XA2 (GP27) XA3-XA10 (GP40GP47) XA11-XA18 (GP50GP57)
70 71 72 73-80
O I/O12t O I/O12t O I/O12t O I/O12t
81-84 86-89
O I/O12t
4.6
POWER PINS
PIN FUNCTION
SYMBOL
VCC3V VCC GND
15, 51 40, 90 10, 35, 61, 85
+3.3V power supply for core logic and driving 3V on host interface. +5V or +3.3V power supply for device output pad. Ground.
- 20 -
W83L517D/W83L517D-F
5. LPC (LOW PIN COUNT) INTERFACE
LPC interface is to replace ISA interface serving as a bus interface between host (chip-set) and peripheral (Winbond I/O). Data transfer on the LPC bus are serialized over a 4 bit bus. The general characteristics of the interface implemented in Winbond LPC I/O are: * * * * * * * One control line, namely LFRAME#, which is used by the host to start or stop transfers. No peripherals drive this signal. The LAD[3:0] bus, which communicates information serially. The information conveyed are cycle type, cycle direction, chip selection, address, data, and wait states. MR (master reset) of Winbond ISA I/O is replaced with a active low reset signal, namely LRESET#, in Winbond LPC I/O. An additional 33 MHz PCI clock is needed in Winbond LPC I/O for synchronization. DMA requests are issued through LDRQ#. Interrupt requests are issued through SERIRQ. Power management events are issued through PME#.
Comparing to its ISA counterpart, LPC implementation saves up to 40 pin counts free for integrating more devices on a single chip. The transition from ISA to LPC is transparent in terms of software which means no BIOS or device driver update is needed except chip-specific configuration.
6. FDC FUNCTIONAL DESCRIPTION
6.1 W83L517D FDC
The floppy disk controller of the W8369L517D integrates all of the logic required for floppy disk control. The FDC implements a PC/AT or PS/2 solution. All programmable options default to compatible values. The FIFO provides better system performance in multi-master systems. The digital data separator supports up to 2 M bits/sec data rate. The FDC includes the following blocks: AT interface, Precompensation, Data Rate Selection, Digital Data Separator, FIFO, and FDC Core.
6.1.1
AT interface
The interface consists of the standard asynchronous signals: RD#, WR#, A0-A3, IRQ, DMA control, and a data bus. The address lines select between the configuration registers, the FIFO and control/status registers. This interface can be switched between PC/AT, Model 30, or PS/2 normal modes. The PS/2 register sets are a superset of the registers found in a PC/AT.
6.1.2
FIFO (Data)
The FIFO is 16 bytes in size and has programmable threshold values. All command parameter information and disk data transfers go through the FIFO. Data transfers are governed by the RQM and DIO bits in the Main Status Register. The FIFO defaults to disabled mode after any form of reset. This maintains PC/AT hardware compatibility. The default values can be changed through the CONFIGURE command. The advantage of the FIFO is that it allows the system a larger DMA latency without causing disk errors. The following tables give several examples of the delays with a FIFO. The data are based upon the following formula: Publication Release Date: May 23, 2005 Revision 1.0
- 21 -
W83L517D/W83L517D-F
THRESHOLD # x (1/DATA/RATE) *8 - 1.5 S = DELAY
FIFO THRESHOLD
MAXIMUM DELAY TO SERVICING AT 500K BPS
Data Rate 1 Byte 2 Byte 8 Byte 15 Byte
FIFO THRESHOLD
1 x 16 S - 1.5 S = 14.5 S 2 x 16 S - 1.5 S = 30.5 S 8 x 16 S - 1.5 S = 6.5 S 15 x 16 S - 1.5 S = 238.5 S
MAXIMUM DELAY TO SERVICING AT 1M BPS
Data Rate 1 Byte 2 Byte 8 Byte 15 Byte 1 x 8 S - 1.5 S = 6.5 S 2 x 8 S - 1.5 S = 14.5 S 8 x 8 S - 1.5 S = 62.5 S 15 x 8 S - 1.5 S = 118.5 S
At the start of a command the FIFO is always disabled and command parameters must be sent based upon the RQM and DIO bit settings in the main status register. When the FDC enters the command execution phase, it clears the FIFO of any data to ensure that invalid data are not transferred. An overrun and underrun will terminate the current command and the data transfer. Disk writes will complete the current sector by generating a 00 pattern and valid CRC. Reads require the host to remove the remaining data so that the result phase may be entered. DMA transfers are enabled with the SPECIFY command and are initiated by the FDC by activating the DRQ pin during a data transfer command. The FIFO is enabled directly by asserting DACK# and addresses need not be valid. Note that if the DMA controller is programmed to function in verify mode a pseudo read is performed by the FDC based only on DACK#. This mode is only available when the FDC has been configured into byte mode (FIFO disabled) and is programmed to do a read. With the FIFO enabled the above operation is performed by using the new VERIFY command. No DMA operation is needed.
6.1.3
Data Separator
The function of the data separator is to lock onto the incoming serial read data. When a lock is achieved the serial front end logic of the chip is provided with a clock which is synchronized to the read data. The synchronized clock, called the Data Window, is used to internally sample the serial data portion of the bit cell, and the alternate state samples the clock portion. Serial to parallel conversion logic separates the read data into clock and data bytes. The Digital Data Separator (DDS) has three parts: control logic, error adjustment, and speed tracking. The DDS circuit cycles once every 12 clock cycles ideally. Any data pulse input will be synchronized and then adjusted by immediate error adjustment. The control logic will generate RDD and RWD for every pulse input. During any cycle where no data pulse is present, the DDS cycles are based on speed. A digital integrator is used to keep track of the speed changes in the input data stream.
- 22 -
W83L517D/W83L517D-F
6.1.4 Write Precompensation
The write precompensation logic is used to minimize bit shifts in the RDDATA stream from the disk drive. Shifting of bits is a known phenomenon in magnetic media and is dependent on the disk media and the floppy drive. The FDC monitors the bit stream that is being sent to the drive. The data patterns that require precompensation are well known. Depending upon the pattern, the bit is shifted either early or late relative to the surrounding bits.
6.1.5
Perpendicular Recording Mode
The FDC is also capable of interfacing directly to perpendicular recording floppy drives. Perpendicular recording differs from the traditional longitudinal method in that the magnetic bits are oriented vertically. This scheme packs more data bits into the same area. FDCs with perpendicular recording drives can read standard 3.5" floppy disks and can read and write perpendicular media. Some manufacturers offer drives that can read and write standard and perpendicular media in a perpendicular media drive. A single command puts the FDC into perpendicular mode. All other commands operate as they normally do. The perpendicular mode requires a 1 Mbps data rate for the FDC. At this data rate the FIFO eases the host interface bottleneck due to the speed of data transfer to or from the disk.
6.1.6
FDC Core
The W83L517D FDC is capable of performing twenty commands. Each command is initiated by a multi-byte transfer from the microprocessor. The result can also be a multi-byte transfer back to the microprocessor. Each command consists of three phases: command, execution, and result. Command The microprocessor issues all required information to the controller to perform a specific operation. Execution The controller performs the specified operation. Result After the operation is completed, status information and other housekeeping information is provided to the microprocessor.
6.1.7
C: D: DIR:
FDC Commands
Cylinder number 0 - 256 Data Pattern Step Direction DIR = 0, step out DIR = 1, step in
Command Symbol Descriptions:
DS0:
Disk Drive Select 0 Publication Release Date: May 23, 2005 Revision 1.0
- 23 -
W83L517D/W83L517D-F
DS1: DTL: EC: EOT: EFIFO: EIS: EOT: FIFOTHR: GAP: GPL: H: HDS: HLT: HUT: LOCK: MFM: MT: N: NCN: ND: OW: PCN: POLL: PRETRK: R: RCN: R/W: SC: SK: SRT: ST0: ST1: ST2: ST3: WG: Disk Drive Select 1 Data Length Enable Count End of Track Enable FIFO Enable Implied Seek End of track FIFO Threshold Gap length selection Gap Length Head number Head number select Head Load Time Head Unload Time Lock EFIFO, FIFOTHR, PTRTRK bits prevent affected by software reset MFM or FM Mode Multitrack The number of data bytes written in a sector New Cylinder Number Non-DMA Mode Overwritten Present Cylinder Number Polling Disable Precompensation Start Track Number Record Relative Cylinder Number Read/Write Sector/per cylinder Skip deleted data address mark Step Rate Time Status Register 0 Status Register 1 Status Register 2 Status Register 3 Write gate alters timing of WE
- 24 -
W83L517D/W83L517D-F
(1) Read Data
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W W W W W W W W W
MT MFM 0 0
SK 0
0 0
0 0
1
1
0
Command codes Sector ID information prior to command execution
HDS DS1 DS0
---------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------------------------- EOT ------------------------------------------ GPL ------------------------------------------ DTL -----------------------
Execution Result R R R R R R R -------------------- ST0 ------------------------------------------ ST1 ------------------------------------------ ST2 -------------------------------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------
Data transfer between the FDD and system Status information after command execution
Sector ID information after command execution
- 25 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
(2) Read Deleted Data
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W W W W W W W W W
MT MFM SK 0 0 0
0 0
1 0
1
0
0
Command codes Sector ID information prior to command execution
HDS DS1 DS0
---------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------------------------- EOT ------------------------------------------ GPL ------------------------------------------ DTL -----------------------
Execution Result R R R R R R R -------------------- ST0 ------------------------------------------ ST1 ------------------------------------------ ST2 -------------------------------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------
Data transfer between the FDD and system Status information after command execution
Sector ID information after command execution
- 26 -
W83L517D/W83L517D-F
(3) Read A Track
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W W W W W W W W W
0 0
MFM 0
0 0
0 0
0 0
0
1
0
Command codes Sector ID information prior to command execution
HDS DS1 DS0
---------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------------------------- EOT ------------------------------------------ GPL ------------------------------------------ DTL -----------------------
Execution
Data transfer between the FDD and system; FDD reads contents of all cylinders from index hole to EOT R R R R R R R -------------------- ST0 ------------------------------------------ ST1 ------------------------------------------ ST2 -------------------------------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N -----------------------Sector ID information after command execution Status information after command execution
Result
- 27 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
(4) Read ID
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command Execution
W W
0 0
MFM 0
0 0
0 0
1 0
0
1
0
Command codes The first correct ID information on the cylinder is stored in Data Register
HDS DS1 DS0
Result
R R R R R R R
-------------------- ST0 ------------------------------------------ ST1 ------------------------------------------ ST2 -------------------------------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------
Status information after command execution
Disk status after the command has been completed
(5) Verify
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W W W W W W W W
MT MFM SK EC 0 0
1 0
0 0
1
1
0
Command codes Sector ID information prior to command execution
HDS DS1 DS0
---------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------------------------- EOT ------------------------------------------ GPL ------------------------------------------ DTL/SC -------------------
Execution Result R R R R R R R -------------------- ST0 ------------------------------------------ ST1 ------------------------------------------ ST2 -------------------------------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------
No data transfer takes place Status information after command execution
Sector ID information after command execution
- 28 -
W83L517D/W83L517D-F
(6) Version
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command Result (7) Write Data
PHASE
W R
0 1
0 0
0 0
1 1
0 0
0 0
0 0
0 0
Command code Enhanced controller
R/W
D7
D6
D5
D4
D3
D2
D1
D0
REMARKS
Command
W W W W W W W W W
MT MFM 0 0
0 0
0 0
0 0
1
0
1
Command codes Sector ID information prior to Command execution
HDS DS1 DS0
---------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------------------------- EOT ------------------------------------------ GPL ------------------------------------------ DTL -----------------------
Execution Result R R R R R R R -------------------- ST0 ------------------------------------------ ST1 ------------------------------------------ ST2 -------------------------------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------
Data transfer between the FDD and system Status information after Command execution
Sector ID information after Command execution
- 29 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
(8) Write Deleted Data
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W W W W W W W W W
MT MFM 0 0
0 0
0 0
1 0
0
0
1
Command codes Sector ID information prior to command execution
HDS DS1 DS0
---------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------------------------- EOT ------------------------------------------ GPL ------------------------------------------ DTL -----------------------
Execution Result R R R R R R R -------------------- ST0 ------------------------------------------ ST1 ------------------------------------------ ST2 -------------------------------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------
Data transfer between the FDD and system Status information after command execution
Sector ID information after command execution
- 30 -
W83L517D/W83L517D-F
(9) Format A Track
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W W W W W W
0 0
MFM 0
0 0
0 0
1 0
1
0
1
Command codes Bytes/Sector Sectors/Cylinder Gap 3 Filler Byte Input Sector Parameters
HDS DS1 DS0
---------------------- N -------------------------------------------- SC ------------------------------------------- GPL ------------------------------------------ D --------------------------------------------- C --------------------------------------------- H --------------------------------------------- R --------------------------------------------- N ------------------------------------------- ST0 ------------------------------------------ ST1 ------------------------------------------ ST2 -------------------------------------- Undefined ---------------------------------- Undefined ---------------------------------- Undefined ---------------------------------- Undefined -------------------
Execution for Each Sector Repeat: Result
W W W W R R R R R R R
Status information after command execution
(10) Recalibrate
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W W
0 0
0 0
0 0
0 0
0 0
1 0
1
1
Command codes Head retracted to Track 0 Interrupt
DS1 DS0
Execution (11) Sense Interrupt Status
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0
REMARKS
Command Result
W R R
0
0
0
0
1
0
0
0
Command code Status information at the end of each seek operation
---------------- ST0 ---------------------------------------- PCN -------------------------
- 31 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
(12) Specify
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W W W
0
0
0
0
0
0
1
1
Command codes
| ---------SRT ----------- | --------- HUT ---------- | |------------ HLT ----------------------------------| ND
(13) Seek
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W W W
0 0
0 0
0 0
0 0
1 0
1
1
1
Command codes
HDS DS1 DS0 Head positioned over proper cylinder on diskette
-------------------- NCN -----------------------
Execution (14) Configure
PHASE
R
R/W
D7
D6
D5
D4
D3
D2
D1
D0
REMARKS
Command
W W W W
0 0 0
0 0
0 0
1 0
0 0
0 0
1 0
1 0
Configure information
EIS EFIFO POLL | ------ FIFOTHR ----| Internal registers written
| --------------------PRETRK ----------------------- |
Execution (15) Relative Seek
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0
REMARKS
Command
W W W
1 0
DIR 0
0 0
0 0
1 0
1
1
1
Command codes
HDS DS1 DS0
| -------------------- RCN ---------------------------- |
- 32 -
W83L517D/W83L517D-F
(16) Dumpreg
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W R R R R
0
0
0
0
1
1
1
0
Registers placed in FIFO
----------------------- PCN-Drive 0------------------------------------------ PCN-Drive 1 ----------------------------------------- PCN-Drive 2------------------------------------------ PCN-Drive 3 --------------------------SRT ------------------ | --------- HUT ------------------ HLT -----------------------------------| ND ------------------------ SC/EOT ---------------------LOCK 0 D3 D2 D1 D0 GAP WG 0 EIS EFIFO POLL | ------ FIFOTHR ------------------------------PRETRK -------------------------
Result
R R R R R R
(17) Perpendicular Mode
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command
W W
0 OW
0 0
0 D3
1 D2
0 D1
0
1
0
Command Code
D0 GAP WG
(18) Lock
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command Result
W R
LOCK 0 0 0
0 0
1 LOCK
0 0
1 0
0 0
0 0
Command Code
(19) Sense Drive Status
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command Result
W W R
0 0
0 0
0 0
0 0
0 0
1
0
0
Command Code Status information about disk drive
HDS DS1 DS0
---------------- ST3 -------------------------
(20) Invalid
PHASE R/W D7 D6 D5 D4 D3 D2 D1 D0 REMARKS
Command Result
W R
------------- Invalid Codes ------------------------------------ ST0 ----------------------
Invalid codes (no operationFDC goes to standby state) ST0 = 80H
- 33 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
6.2 Register Descriptions
ADDRESS OFFSET READ REGISTER WRITE
There are several status, data, and control registers in W83L517D. These registers are defined below:
base address + 0 base address + 1 base address + 2 base address + 3 base address + 4 base address + 5 base address + 7
SA REGISTER SB REGISTER DO REGISTER TD REGISTER MS REGISTER DT (FIFO) REGISTER DI REGISTER TD REGISTER DR REGISTER DT (FIFO) REGISTER CC REGISTER
6.2.1
Status Register A (SA Register) (Read base address + 0)
This register is used to monitor several disk interface pins in PS/2 and Model 30 modes. In PS/2 mode, the bit definitions for this register are as follows:
7
6
5
4
3
2
1
0
DIR WP INDEX HEAD TRAK0 STEP DRV2 INIT PENDING
INIT PENDING (Bit 7): This bit indicates the value of the floppy disk interrupt output. DRV2# (Bit 6): 0 1 A second drive has been installed A second drive has not been installed
STEP (Bit 5): This bit indicates the complement of STEP# output. TRAK0# (Bit 4): This bit indicates the value of TRAK0# input.
- 34 -
W83L517D/W83L517D-F
HEAD (Bit 3): This bit indicates the complement of HEAD# output. 0 1 side 0 side 1
INDEX# (Bit 2): This bit indicates the value of INDEX# output. WP# (Bit 1): 0 1 disk is write-protected disk is not write-protected
DIR (Bit 0) This bit indicates the direction of head movement. 0 1 outward direction inward direction
In PS/2 Model 30 mode, the bit definitions for this register are as follows:
7 6 5 4 3 2 1
0
DIR WP INDEX HEAD TRAK0 STEP F/F DRQ INIT PENDING
INIT PENDING (Bit 7): This bit indicates the value of the floppy disk interrupt output. DRQ (Bit 6): This bit indicates the value of DRQ output pin. STEP F/F (Bit 5): This bit indicates the complement of latched STEP# output. TRAK0 (Bit 4): This bit indicates the complement of TRAK0# input. HEAD# (Bit 3): This bit indicates the value of HEAD# output. 0 side 1
- 35 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
1 side 0
INDEX (Bit 2): This bit indicates the complement of INDEX# output. WP (Bit 1): 0 1 disk is not write-protected disk is write-protected
DIR# (Bit 0) This bit indicates the direction of head movement. 0 1 inward direction outward direction
6.2.2
Status Register B (SB Register) (Read base address + 1)
This register is used to monitor several disk interface pins in PS/2 and Model 30 modes. In PS/2 mode, the bit definitions for this register are as follows:
7 1
6 1
5
4
3
2
1
0
MOT EN A MOT EN B WE RDATA Toggle WDATA Toggle Drive SEL0
Drive SEL0 (Bit 5): This bit indicates the status of DO REGISTER bit 0 (drive select bit 0). WDATA Toggle (Bit 4): This bit changes state at every rising edge of the WD# output pin. RDATA Toggle (Bit 3): This bit changes state at every rising edge of the RDATA# output pin. WE (Bit 2): This bit indicates the complement of the WE# output pin. MOT EN B (Bit 1) This bit indicates the complement of the MOB# output pin. MOT EN A (Bit 0) This bit indicates the complement of the MOA# output pin. In PS/2 Model 30 mode, the bit definitions for this register are as follows: - 36 -
W83L517D/W83L517D-F
7
6
5
4
3
2
1
0
DSC DSD WE F/F RDATA F/F WD F/F DSA DSB DRV2
DRV2# (Bit 7): 0 1 A second drive has been installed A second drive has not been installed
DSB# (Bit 6): This bit indicates the status of DSB# output pin. DSA# (Bit 5): This bit indicates the status of DSA# output pin. WD F/F(Bit 4): This bit indicates the complement of the latched WD# output pin at every rising edge of the WD# output pin. RDATA F/F(Bit 3): This bit indicates the complement of the latched RDATA# output pin . WE F/F (Bit 2): This bit indicates the complement of latched WE# output pin. DSD# (Bit 1): 0 1 0 1 Drive D has been selected Drive D has not been selected Drive C has been selected Drive C has not been selected
DSC# (Bit 0):
- 37 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
6.2.3 Digital Output Register (DO Register) (Write base address + 2)
The Digital Output Register is a write-only register controlling drive motors, drive selection, DRQ/IRQ enable, and FDC resetting. All the bits in this register are cleared by the MR pin. The bit definitions are as follows:
7 6 5 4 3 2 1-0 Drive Select: 00 select drive A 01 select drive B 10 select drive C 11 select drive D Floppy Disk Controller Reset Active low resets FDC DMA and INT Enable Active high enable DRQ/IRQ Motor Enable A. Motor A on when active high Motor Enable B. Motor B on when active high Motor Enable C. Motor C on when active high Motor Enable D. Motor D on when active high
6.2.4
Tape Drive Register (TD Register) (Read base address + 3)
This register is used to assign a particular drive number to the tape drive support mode of the data separator. This register also holds the media ID, drive type, and floppy boot drive information of the floppy disk drive. In normal floppy mode, this register includes only bit 0 and 1. The bit definitions are as follows:
7 X 6 X 5 X 4 X 3 X 2 X Tape sel 0 Tape sel 1 1 0
If three mode FDD function is enabled (EN3MODE = 1 in CR9), the bit definitions are as follows:
7 6 5 4 3 2 1 0
Tape Sel 0 Tape Sel 1 Floppy boot drive 0 Floppy boot drive 1 Drive type ID0 Drive type ID1 Media ID0 Media ID1
- 38 -
W83L517D/W83L517D-F
Media ID1 Media ID0 (Bit 7, 6): These two bits are read only. These two bits reflect the value of CR8 bit 3, 2. Drive type ID1 Drive type ID0 (Bit 5, 4): These two bits reflect two of the bits of CR7. Which two bits are reflected depends on the last drive selected in the DO REGISTER. Floppy Boot drive 1, 0 (Bit 3, 2): These two bits reflect the value of CR8 bit 1, 0. Tape Sel 1, Tape Sel 0 (Bit 1, 0): These two bits assign a logical drive number to the tape drive. Drive 0 is not available as a tape drive and is reserved as the floppy disk boot drive.
TAPE SEL 1 TAPE SEL 0 DRIVE SELECTED
0 0 1 1
0 1 0 1
None 1 2 3
6.2.5
Main Status Register (MS Register) (Read base address + 4)
The Main Status Register is used to control the flow of data between the microprocessor and the controller. The bit definitions for this register are as follows:
7 6 5 4 3 2 1 0
FDD 0 Busy, (D0B = 1), FDD number 0 is in the SEEK mode. FDD 1 Busy, (D1B = 1), FDD number 1 is in the SEEK mode. FDD 2 Busy, (D2B = 1), FDD number 2 is in the SEEK mode. FDD 3 Busy, (D3B = 1), FDD number 3 is in the SEEK mode. FDC Busy, (CB). A read or write command is in the process when CB = HIGH. Non-DMA mode, the FDC is in the non-DMA mode, this bit is set only during the execution phase in non-DMA mode. Transition to LOW state indicates execution phase has ended. DATA INPUT/OUTPUT, (DIO). If DIO= HIGH then transfer is from Data Register to the processor. If DIO = LOW then transfer is from processor to Data Register. Request for Master (RQM). A high on this bit indicates Data Register is ready to send or receive data to or from the processor.
6.2.6
Data Rate Register (DR Register) (Write base address + 4)
The Data Rate Register is used to set the transfer rate and write precompensation. The data rate of the FDC is programmed by the CC REGISTER for PC-AT and PS/2 Model 30 and PS/2 mode, and not by the DR REGISTER. The real data rate is determined by the most recent write to either of the DR REGISTER or CC REGISTER.
- 39 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
7
6
5 0
4
3
2
1
0
DRATE0 DRATE1 PRECOMP0 PRECOMP1 PRECOMP2 POWER DOWN S/W RESET
S/W RESET (Bit 7): This bit is the software reset bit. POWER-DOWN (Bit 6): 0 1 FDC in normal mode FDC in power-down mode
PRECOMP2 PRECOMP1 PRECOMP0 (Bit 4, 3, 2): These three bits select the value of write precompensation. The following tables show the precompensation values for the combination of these bits.
PRECOMP PRECOMPENSATION DELAY
2 0 0 0 0 1 1 1 1
1 0 0 1 1 0 0 1 1
0 0 1 0 1 0 1 0 1
250K - 1 Mbps Default Delays 41.67 nS 83.34 nS 125.00 nS 166.67 nS 208.33 nS 250.00 nS 0.00 nS (disabled)
2 Mbps Tape drive Default Delays 20.8 nS 41.17 nS 62.5nS 83.3 nS 104.2 nS 125.00 nS 0.00 nS (disabled)
DATA RATE
DEFAULT PRECOMPENSATION DELAYS
250 KB/S 300 KB/S 500 KB/S 1 MB/S 2 MB/S
125 nS 125 nS 125 nS 41.67nS 20.8 nS
- 40 -
W83L517D/W83L517D-F
DRATE1 DRATE0 (Bit 1, 0): These two bits select the data rate of the FDC and reduced write current control. 00 500 KB/S (MFM), 250 KB/S (FM), RWC = 1 01 300 KB/S (MFM), 150 KB/S (FM), RWC = 0 10 250 KB/S (MFM), 125 KB/S (FM), RWC = 0 11 1 MB/S (MFM), Illegal (FM), RWC = 1 The 2 MB/S data rate for Tape drive is only supported by setting 01 to DRATE1 and DRATE0 bits, as well as setting 10 to DRT1 and DRT0 bits which are two of the Configure Register CRF4 or CRF5 bits in logic device 0. Please refer to the function description of CRF4 or CRF5 and data rate table for individual data rates setting.
6.2.7
FIFO Register (R/W base address + 5)
The Data Register consists of four status registers in a stack with only one register presented to the data bus at a time. This register stores data, commands, and parameters and provides diskette-drive status information. Data bytes are passed through the data register to program or obtain results after a command. In the W83697HF, this register defaults to FIFO disabled mode after reset. The FIFO can change its value and enable its operation through the CONFIGURE command.
Status Register 0 (ST0)
7-6 5 4 3 2 1-0
US1, US0 Drive Select: 00 Drive A selected 01 Drive B selected 10 Drive C selected 11 Drive D selected HD Head address: 1 Head selected 0 Head selected NR Not Ready: 1 Drive is not ready 0 Drive is ready EC Equipment Check: 1 When a fault signal is received from the FDD or the track 0 signal fails to occur after 77 step pulses 0 No error SE Seek end: 1 seek end 0 seek error IC Interrupt Code: 00 Normal termination of command 01 Abnormal termination of command 10 Invalid command issue 11 Abnormal termination because the ready signal from FDD changed state during command executio
- 41 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Status Register 1 (ST1)
7 6 5 4 3 2 1 0
Missing Address Mark. 1 When the FDC cannot detect the data address mark or the data address mark has been deleted. NW (Not Writable). 1 If a write Protect signal is detected from the diskette drive during execution of write data. ND (No DATA). 1 If specified sector cannot be found during execution of a read, write or verifly data. Not used. This bit is always 0. OR (Over Rum). 1 If the FDC is not serviced by the host system within a certain time interval during data transfer. DE (data Error).1 When the FDC detects a CRC error in either the ID field or the data field. Not used. This bit is always 0. EN (End of track). 1 When the FDC tries to access a sector beyond the final sector of a cylinder.
Status Register 2 (ST2)
7 6 5 4 3 2 1 0
MD (Missing Address Mark in Data Field). 1 If the FDC cannot find a data address mark (or the address mark has been deleted) when reading data from the media 0 No error BC (Bad Cylinder) 1 Bad Cylinder 0 No error SN (Scan Not satisfied) 1 During execution of the Scan command 0 No error SH (Scan Equal Hit) 1 During execution of the Scan command, if the equal condition is satisfied 0 No error WC (Wrong Cylinder) 1 Indicates wrong Cylinder DD (Data error in the Data field) 1 If the FDC detects a CRC error in the data field 0 No error CM (Control Mark) 1 During execution of the read data or scan command 0 No error Not used. This bit is always 0
Status Register 3 (ST3)
7 6 5 4 3 2 1 0
US0 Unit Select 0 US1 Unit Select 1 HD Head Address TS Two-Side TO Track 0 RY Ready WP Write Protected FT Fault
- 42 -
W83L517D/W83L517D-F
6.2.8 Digital Input Register (DI Register) (Read base address + 7)
The Digital Input Register is an 8-bit read-only register used for diagnostic purposes. In a PC/XT or AT only Bit 7 is checked by the BIOS. When the register is read, Bit 7 shows the complement of DSKCHG#, while other bits of the data bus remain in tri-state. Bit definitions are as follows:
7
6
5
4
3
2
1
0
xxxxxxx for hard disk controller x Reservedreadthe this register, these bits are in tri-stat During a of
DSKCHG
In the PS/2 mode, the bit definitions are as follows:
7
6 1
5 1
4 1
3 1
2
1
0
HIGH DENS DRATE0 DRATE1
DSKCHG
DSKCHG (Bit 7): This bit indicates the complement of the DSKCHG# input. Bit 6-3: These bits are always a logic 1 during a read. DRATE1 DRATE0 (Bit 2, 1): These two bits select the data rate of the FDC. Refer to the DR register bits 1 and 0 for the settings corresponding to the individual data rates. HIGH DENS# (Bit 0): 0 1 500 KB/S or 1 MB/S data rate (high density FDD) 250 KB/S or 300 KB/S data rate
In the PS/2 Model 30 mode, the bit definitions are as follows:
- 43 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
7
6 0
5 0
4 0
3
2
1
0
DRATE0 DRATE1 NOPREC DMAEN
DSKCHG
DSKCHG (Bit 7): This bit indicates the status of DSKCHG# input. Bit 6-4: These bits are always a logic 1 during a read. DMAEN (Bit 3): This bit indicates the value of DO REGISTER bit 3. NOPREC (Bit 2): This bit indicates the value of CC REGISTER NOPREC bit. DRATE1 DRATE0 (Bit 1, 0): These two bits select the data rate of the FDC.
6.2.9
Configuration Control Register (CC Register) (Write base address + 7)
This register is used to control the data rate. In the PC/AT and PS/2 mode, the bit definitions are as follows:
7 6 5 4 3 2 1 0
x
x
x
x
x
x
DRATE0 DRATE1
X: Reserved Bit 7-2: Reserved. These bits should be set to 0. DRATE1 DRATE0 (Bit 1, 0): These two bits select the data rate of the FDC. In the PS/2 Model 30 mode, the bit definitions are as follows:
7 X 6 X 5 X 4 X 3 X DRATE0 DRATE1 NOPREC 2 1 0
X: Reserved
- 44 -
W83L517D/W83L517D-F
Bit 7-3: Reserved. These bits should be set to 0. NOPREC (Bit 2): This bit indicates no precompensation. It has no function and can be set by software. DRATE1 DRATE0 (Bit 1, 0): These two bits select the data rate of the FDC.
7. UART PORT
7.1 Universal Asynchronous Receiver/Transmitter (UART A)
The UARTs are used to convert parallel data into serial format on the transmit side and convert serial data to parallel format on the receiver side. The serial format, in order of transmission and reception, is a start bit, followed by five to eight data bits, a parity bit (if programmed) and one, one and half (fivebit format only) or two stop bits. The UARTs are capable of handling divisors of 1 to 65535 and producing a 16x clock for driving the internal transmitter logic. Provisions are also included to use this 16x clock to drive the receiver logic. The UARTs also support the MIDI data rate. Furthermore, the UARTs also include complete modem control capability and a processor interrupt system that may be software trailed to the computing time required to handle the communication link. The UARTs have a FIFO mode to reduce the number of interrupts presented to the CPU. In each UART, there are 16byte FIFOs for both receive and transmit mode.
7.2
7.2.1
Register Address
UART Control Register (UCR) (Read/Write)
The UART Control Register controls and defines the protocol for asynchronous data communications, including data length, stop bit, parity, and baud rate selection.
7
6
5
4
3
2
1
0
Data length select bit 0 (DLS0) Data length select bit 1(DLS1) Multiple stop bits enable (MSBE) Parity bit enable (PBE) Even parity enable (EPE) Parity bit fixed enable (PBFE) Set silence enable (SSE) Baudrate divisor latch access bit (BDLAB)
- 45 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 7: BDLAB. When this bit is set to a logical 1, designers can access the divisor (in 16-bit binary format) from the divisor latches of the baudrate generator during a read or write operation. When this bit is reset, the Receiver Buffer Register, the Transmitter Buffer Register, or the Interrupt Control Register can be accessed. Bit 6: SSE. A logical 1 forces the Serial Output (SOUT) to a silent state (a logical 0). Only IRTX is affected by this bit; the transmitter is not affected. Bit 5: PBFE. When PBE and PBFE of UCR are both set to a logical 1, (1) if EPE is logical 1, the parity bit is fixed as logical 0 to transmit and check. (2) if EPE is logical 0, the parity bit is fixed as logical 1 to transmit and check. TABLE 7-1 UART Register Bit Map
BIT NUMBER REGISTER ADDRESS BASE
+0
0
1
RX Data Bit 1
2
3
4
RX Data Bit 4
5
RX Data Bit 5
6
7
Receiver RX Data Buffer Bit 0 RBR BDLAB Register =0 (Read Only) Transmitter TX Data Buffer TBR BDLAB Register Bit 0 =0 (Write Only) +0 +1 BDLAB =0 Interrupt Control Register Interrupt Status Register (Read Only) RBR Data Ready Interrupt Enable (ERDRI) "0" if Interrupt Pending
RX Data RX Data Bit 2 Bit 3
RX Data RX Data Bit 6 Bit 7
TX Data Bit 1 TBR Empty Interrupt Enable (ETBREI) Interrupt Status Bit (0) RCVR FIFO Reset Data Length Select Bit 1 (DLS1) Request to Send (RTS)
TX Data Bit 2
TX Data Bit 3
TX Data Bit 4
TX Data Bit 5
TX Data TX Data Bit 6 Bit 7
ICR
USR HSR Interrupt Interrupt Enable Enable (EUSRI) Interrupt Status Bit (1) XMIT FIFO Reset (EHSRI) Interrupt Status Bit (2)** DMA Mode Select
0
0
0
0
FIFOs 0 0 **
FIFOs **
+2
ISR
Enabled Enabled RX RX Interrupt Interrupt Active Active Level Level (MSB) (LSB) Set Silence Enable (SSE) Baudrate Divisor Latch Access Bit (BDLAB) 0
+2
UART FIFO Control UFR Register (Write Only)
FIFO Enable
Reserved Reversed
+3
UART Control Register
UCR
Data Length Select Bit 0 (DLS0)
Multiple Stop Bits Enable (MSBE) Loopback RI Input
Parity Bit Enable (PBE)
Even Parity Enable (EPE) Internal Loopba ck Enable
Parity Bit Fixed Enable PBFE)
+4
Data Handshake Terminal Control HCR Ready Register (DTR)
IRQ Enable
0
0
- 46 -
W83L517D/W83L517D-F
UART Register Bit Map, continued.
BIT NUMBER REGISTER ADDRESS BASE
UART Status Register
0
RBR Data Ready (RDR) CTS Toggling HSR (TCTS) UDR Bit 0
1
Overrun Error (OER) DSR Toggling (TDSR) Bit 1
2
3
4
5
6
7
+5
USR
RX FIFO Silent TBR TSR Parity Bit No Stop Error Byte Bit Error Detecte Empty Empty Indicatio Error d (TBRE) (TSRE) n (RFEI) (PBER) (NSER) ** (SBD) RI Falling DCD Clear Edge Toggling to Send (FERI) Bit 2 (TDCD) Bit 3 (CTS) Bit 4 Data Ring Set Indicator Ready (RI) (DSR) Bit 5 Bit 6 Data Carrier Detect (DCD) Bit 7
+6
Handshake Status Register User Defined Register
+7 +0
Baudrate Divisor BDLAB Latch Low =1 +1
BLL
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Baudrate Divisor BHL BDLAB Latch High =1
Bit 8
Bit 9
Bit 10
Bit 11
Bit 12
Bit 13
Bit 14
Bit 15
*: Bit 0 is the least significant bit. The least significant bit is the first bit serially transmitted or received. **: These bits are always 0 in 16450 Mode.
Bit 4: EPE. This bit describes the number of logic 1's in the data word bits and parity bit only when bit 3 is programmed. When this bit is set, an even number of logic 1's are sent or checked. When the bit is reset, an odd number of logic 1's are sent or checked. Bit 3: PBE. When this bit is set, the position between the last data bit and the stop bit of the SOUT will be stuffed with the parity bit at the transmitter. For the receiver, the parity bit in the same position as the transmitter will be detected. Bit 2: MSBE. This bit defines the number of stop bits in each serial character that is transmitted or received. (1) If MSBE is set to a logical 0, one stop bit is sent and checked. (2) If MSBE is set to a logical 1, and data length is 5 bits, one and a half stop bits are sent and checked. (3) If MSBE is set to a logical 1, and data length is 6, 7, or 8 bits, two stop bits are sent and checked. Bits 0 and 1: DLS0, DLS1. These two bits define the number of data bits that are sent or checked in each serial character.
- 47 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
TABLE 7-2 WORD LENGTH DEFINITION
DLS1 DLS0 DATA LENGTH
0 0 1 1
0 1 0 1
5 bits 6 bits 7 bits 8 bits
7.2.2
UART Status Register (USR) (Read/Write)
This 8-bit register provides information about the status of the data transfer during communication.
7
6
5
4
3
2
1
0
RBR Data ready (RDR) Overrun error (OER) Parity bit error (PBER) No stop bit error (NSER) Silent byte detected (SBD) Transmitter Buffer Register empty (TBRE) Transmitter Shift Register empty (TSRE) RX FIFO Error Indication (RFEI)
Bit 7: RFEI. In 16450 mode, this bit is always set to a logic 0. In 16550 mode, this bit is set to a logic 1 when there is at least one parity bit error, no stop bit error or silent byte detected in the FIFO. In 16550 mode, this bit is cleared by reading from the USR if there are no remaining errors left in the FIFO. Bit 6: TSRE. In 16450 mode, when TBR and TSR are both empty, this bit will be set to a logical 1. In 16550 mode, if the transmit FIFO and TSR are both empty, it will be set to a logical 1. Other thanthese two cases, this bit will be reset to a logical 0. Bit 5: TBRE. In 16450 mode, when a data character is transferred from TBR to TSR, this bit will be set to a logical 1. If ETREI of ICR is a logical 1, an interrupt will be generated to notify the CPU to write the next data. In 16550 mode, this bit will be set to a logical 1 when the transmit FIFO is empty. It will be reset to a logical 0 when the CPU writes data into TBR or FIFO. Bit 4: SBD. This bit is set to a logical 1 to indicate that received data are kept in silent state for a full word time, including start bit, data bits, parity bit, and stop bits. In 16550 mode, it indicates the same condition for the data on top of the FIFO. When the CPU reads USR, it will clear this bit to a logical 0. Bit 3: NSER. This bit is set to a logical 1 to indicate that the received data have no stop bit. In 16550 mode, it indicates the same condition for the data on top of the FIFO. When the CPU reads USR, it will clear this bit to a logical 0. Bit 2: PBER. This bit is set to a logical 1 to indicate that the parity bit of received data is wrong. In 16550 mode, it indicates the same condition for the data on top of the FIFO. When the CPU reads USR, it will clear this bit to a logical 0.
- 48 -
W83L517D/W83L517D-F
Bit 1: OER. This bit is set to a logical 1 to indicate received data have been overwritten by the next received data before they were read by the CPU. In 16550 mode, it indicates the same condition instead of FIFO full. When the CPU reads USR, it will clear this bit to a logical 0. Bit 0: RDR. This bit is set to a logical 1 to indicate received data are ready to be read by the CPU in the RBR or FIFO. After no data are left in the RBR or FIFO, the bit will be reset to a logical 0.
7.2.3
Handshake Control Register (HCR) (Read/Write)
This register controls the pins of the UART used for handshaking peripherals such as modem, and controls the diagnostic mode of the UART.
7 0
6 0
5 0
4
3
2
1
0
Data terminal ready (DTR) Request to send (RTS) Loopback RI input IRQ enable Internal loopback enable
Bit 4: When this bit is set to a logical 1, the UART enters diagnostic mode by an internal loopback, as follows: (1) SOUT is forced to logical 1, and SIN is isolated from the communication link instead of the TSR. (2) Modem output pins are set to their inactive state. (3) Modem input pins are isolated from the communication link and connect internally as DTR (bit 0 of HCR) DSR, RTS ( bit 1 of HCR) CTS, Loopback RI input ( bit 2 of HCR) RI and IRQ enable ( bit 3 of HCR) DCD . Aside from the above connections, the UART operates normally. This method allows the CPU to test the UART in a convenient way. Bit 3: The UART interrupt output is enabled by setting this bit to a logic 1. In the diagnostic mode this bit is internally connected to the modem control input DCD . Bit 2: This bit is used only in the diagnostic mode. connected to the modem control input RI . Bit 1: This bit controls the RTS output. The value of this bit is inverted and output to RTS . Bit 0: This bit controls the DTR output. The value of this bit is inverted and output to DTR . In the diagnostic mode this bit is internally
- 49 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
7.2.4 Handshake Status Register (HSR) (Read/Write)
This register reflects the current state of four input pins for handshake peripherals such as a modem and records changes on these pins.
7
6
5
4
3
2
1
0
CTS toggling (TCTS) DSR toggling (TDSR) RI falling edge (FERI) DCD toggling (TDCD) Clear to send (CTS) Data set ready (DSR) Ring indicator (RI) Data carrier detect (DCD)
Bit 7: This bit is the opposite of the DCD input. This bit is equivalent to bit 3 of HCR in loopback mode. Bit 6: This bit is the opposite of the RI input. This bit is equivalent to bit 2 of HCR in loopback mode. Bit 5: This bit is the opposite of the DSR input. This bit is equivalent to bit 0 of HCR in loopback mode. Bit 4: This bit is the opposite of the CTS input. This bit is equivalent to bit 1 of HCR in loopback mode. Bit 3: TDCD. This bit indicates that the DCD pin has changed state after HSR was read by the CPU. Bit 2: FERI. This bit indicates that the RI pin has changed from low to high state after HSR was read by the CPU. Bit 1: TDSR. This bit indicates that the DSR pin has changed state after HSR was read by the CPU. Bit 0: TCTS. This bit indicates that the CTS pin has changed state after HSR was read.
- 50 -
W83L517D/W83L517D-F
7.2.5 UART FIFO Control Register (UFR) (Write only)
This register is used to control the FIFO functions of the UART.
7 6 5 4 3 2 1 0
FIFO enable Receiver FIFO reset Transmitter FIFO reset DMA mode select Reserved Reserved RX interrupt active level (LSB) RX interrupt active level (MSB)
Bit 6, 7: These two bits are used to set the active level for the receiver FIFO interrupt. For example, if the interrupt active level is set as 4 bytes, once there are more than 4 data characters in the receiver FIFO, the interrupt will be activated to notify the CPU to read the data from the FIFO. TABLE 7-3 FIFO TRIGGER LEVEL
BIT 7 BIT 6 RX FIFO INTERRUPT ACTIVE LEVEL (BYTES)
0 0 1 1 Bit 4, 5: Bit 3: mode 1 if
0 1 0 1 Reserved
01 04 08 14
When this bit is programmed to logic 1, the DMA mode will change from mode 0 to UFR bit 0 = 1.
Bit 2: Setting this bit to a logical 1 resets the TX FIFO counter logic to initial state. This bit will clear to a logical 0 by itself after being set to a logical 1. Bit 1: Setting this bit to a logical 1 resets the RX FIFO counter logic to initial state. This bit will clear to a logical 0 by itself after being set to a logical 1. Bit 0: This bit enables the 16550 (FIFO) mode of the UART. This bit should be set to a logical 1 before other bits of UFR are programmed.
- 51 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
7.2.6 Interrupt Status Register (ISR) (Read only)
This register reflects the UART interrupt status, which is encoded by different interrupt sources into 3 bits.
7
6
5 0
4 0
3
2
1
0
0 if interrupt pending Interrupt Status bit 0 Interrupt Status bit 1 Interrupt Status bit 2 FIFOs enabled FIFOs enabled
Bit 7, 6: Bit 5, 4:
These two bits are set to a logical 1 when UFR bit 0 = 1. These two bits are always logic 0.
Bit 3: In 16450 mode, this bit is 0. In 16550 mode, both bit 3 and 2 are set to a logical 1 when a timeout interrupt is pending. Bit 2, 1: below. These two bits identify the priority level of the pending interrupt, as shown in the table
Bit 0: This bit is a logical 1 if there is no interrupt pending. If one of the interrupt sources has occurred, this bit will be set to a logical 0.
- 52 -
W83L517D/W83L517D-F
TABLE 7-4 INTERRUPT CONTROL FUNCTION
ISR INTERRUPT SET AND FUNCTION
Bit 3 0 0
Bit 2 0 1
Bit 1 0 1
Bit 0 1 0
Interrupt priority First
Interrupt Type UART Receive Status RBR Data Ready
Interrupt Source
Clear Interrupt Read USR 1. Read RBR 2. Read RBR until FIFO data under active level Read RBR 1. Write data into TBR
No Interrupt pending 1. OER = 1 2. PBER =1
3. NSER = 1 4. SBD = 1 1. RBR data ready 2. FIFO interrupt active level reached Data present in RX FIFO for 4 characters period of time since last access of RX FIFO. TBR empty 1. TCTS = 1 2. TDSR = 1 3. FERI = 1 4. TDCD = 1
0
1
0
0
Second
1
1
0
0
Second
FIFO Data Timeout
0
0
1
0
Third
TBR Empty Handshake status
2. Read ISR (if priority is third) Read HSR
0
0
0
0
Fourth
** Bit 3 of ISR is enabled when bit 0 of UFR is logical 1.
7.2.7
Interrupt Control Register (ICR) (Read/Write)
This 8-bit register allows the five types of controller interrupts to activate the interrupt output signal separately. The interrupt system can be totally disabled by resetting bits 0 through 3 of the Interrupt Control Register (ICR). A selected interrupt can be enabled by setting the appropriate bits of this register to a logical 1.
7 0
6 0
5 0
4 0
3
2
1
0
RBR data ready interrupt enable (ERDRI) TBR empty interrupt enable (ETBREI) UART receive status interrupt enable (EUSRI) Handshake status interrupt enable (EHSRI)
- 53 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 7-4: These four bits are always logic 0. Bit 3: EHSRI. Setting this bit to a logical 1 enables the handshake status register interrupt. Bit 2: EUSRI. Setting this bit to a logical 1 enables the UART status register interrupt. Bit 1: ETBREI. Setting this bit to a logical 1 enables the TBR empty interrupt. Bit 0: ERDRI. Setting this bit to a logical 1 enables the RBR data ready interrupt.
7.2.8
Programmable Baud Generator (BLL/BHL) (Read/Write)
16
Two 8-bit registers, BLL and BHL, compose a programmable baud generator that uses 24 MHz to generate a 1.8461 MHz frequency and divides it by a divisor from 1 to 2 -1. The output frequency of the baud generator is the baud rate multiplied by 16, and this is the base frequency for the transmitter and receiver. The table in the next page illustrates the use of the baud generator with a frequency of 1.8461 MHz. In high-speed UART mode (refer to CR0C bit7 and CR0C bit6), the programmable baud generator directly uses 24 MHz and the same divisor as the normal speed divisor. In high-speed mode, the data transmission rate can be as high as 1.5M bps.
7.2.9
User-defined Register (UDR) (Read/Write)
TABLE 7-5 BAUD RATE TABLE
BAUD RATE FROM DIFFERENT PRE-DIVIDER DECIMAL DIVISOR USED TO GENERATE 16X CLOCK ERROR PERCENTAGE BETWEEN DESIRED AND ACTUAL
This is a temporary register that can be accessed and defined by the user.
PRE-DIV: 13 1.8461M HZ
PRE-DIV:1.625 14.769M HZ
PRE-DIV: 1.0 24M HZ
50 75 110 134.5 150 300 600 1200 1800 2000 2400 3600 4800 7200 9600
400 600 880 1076 1200 2400 4800 9600 14400 16000 19200 28800 38400 57600 76800
650 975 1430 1478.5 1950 3900 7800 15600 23400 26000 31200 46800 62400 93600 124800
2304 1536 1047 857 768 384 192 96 64 58 48 32 24 16 12
** ** 0.18% 0.099% ** ** ** ** ** 0.53% ** ** ** ** **
- 54 -
W83L517D/W83L517D-F
BAUD RATE TABLE, continued.
BAUD RATE FROM DIFFERENT PRE-DIVIDER PRE-DIV: 13 1.8461M HZ PRE-DIV:1.625 14.769M HZ PRE-DIV: 1.0 24M HZ DECIMAL DIVISOR USED TO GENERATE 16X CLOCK ERROR PERCENTAGE BETWEEN DESIRED AND ACTUAL
19200 38400 57600 115200
153600 307200 460800 921600
249600 499200 748800 1497600
6 3 2 1
** ** ** **
** The percentage error for all baud rates, except where indicated otherwise, is 0.16%.
Note. Pre-Divisor is determined by CRF0 of UART A
8. INFRARED (IR) PORT
The Infrared (IR) function provides a point-to-point (or multi-point to multi-point) wireless communication which can operate under various transmission protocols including IrDA 1.0 SIR, IrDA 1.1 MIR (1.152 Mbps), IrDA 1.1 FIR (4 Mbps), SHARP ASK-IR, and remote control (NEC, RC-5, advanced RC-5, and RECS-80 protocol).
8.1
IR Register Description
When bank select enable bit (ENBNKSEL, the bit 0 in CRF0 of logic device 6) is set, legacy IR will be switched to Advanced IR, and eight Register Sets can then be accessible. These Register Sets control enhanced IR, SIR, MIR, or FIR. Also a superior traditional SIR function can be used with enhanced features such as 32-byte transmitter/receiver FIFOs, non-encoding IRQ identify status register, and automatic flow control. The MIR/FIR and remote control registers are also defined in these Register Sets. Structure of these Register Sets is asshown below.
- 55 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Reg 7 Reg 6 Reg 5 Reg 4 BDL/SSR Reg 2 Reg 1 Reg 0
Set 0 Set 1 Set 2 Set 3 Set 4 Set 5 Set 6 Set 7
All in one Reg to Select SSR
*Set 0, 1 are legacy/Advanced UART Registers *Set 2~7 are Advanced UART Registers
Each of these register sets has a common register, namely Sets Select Register (SSR), in order to switch to another register set. The summary description of these Sets is given below.
SET SETS DESCRIPTION
0 1 2 3 4 5 6 7
Legacy/Advanced IR Control and Status Registers. Legacy Baud Rate Divisor Register. Advanced IR Control and Status Registers. Version ID and Mapped Control Registers. Transmitter/Receiver/Timer Counter Registers and IR Control Registers. Flow Control and IR Control and Frame Status FIFO Registers. IR Physical Layer Control Registers Remote Control and IR front-end Module Selection Registers.
- 56 -
W83L517D/W83L517D-F
8.2 Set0-Legacy/Advanced IR Control and Status Registers
ADDRESS OFFSET REGISTER NAME REGISTER DESCRIPTION
0 1 2 3 4 5 6 7
RBR/TBR ICR ISR/UFR UCR/SSR HCR USR HSR UDR/ESCR
Receiver/Transmitter Buffer Registers Interrupt Control Register Interrupt Status or IR FIFO Control Register IR Control or Sets Select Register Handshake Control Register IR Status Register Handshake Status Register User Defined Register
8.2.1
Set0.Reg0 - Receiver/Transmitter Buffer Registers (RBR/TBR) (Read/Write)
Receiver Buffer Register is read only and Transmitter Buffer Register is write only. When operating in the PIO mode, the port is used to Receive/Transmit 8-bit data. When function as a legacy IR, this port only supports PIO mode. If set in the advanced IR mode and configured as MIR/FIR/Remote IR, this port can support DMA transmission. Two DMA channels can be used simultaneously, one for TX DMA and the other for RX DMA. Therefore, single DMA channel is also supported when the bit of D_CHSW (DMA Channel Swap, in Set2.Reg2.Bit3) is set and the TX/RX DMA channel is swapped. Note that two DMA channels can be defined in configure register CR2A which selects DMA channel or disables DMA channel. If only RX DMA channel is enabled while TX DMA channel is disabled, then the single DMA channel will be selected.
8.2.2
Set0.Reg1 - Interrupt Control Register (ICR)
B7 B6 B5 B4 B3 B2 B1 B0
MODE
Legacy IR Advanced IR
0 ETMRI
0 EFSFI
0 ETXTHI
0 EDMAI
0 0
EUSRI EUSRI/ TXURI
ETBREI ETBREI
ERDRI ERBRI
The advanced IR functions including Advanced SIR/ASK-IR, MIR, FIR, or Remote IR are described below. Bit 7: Legacy IR Mode: Not used. A read will return 0. Advanced IR Mode: ETMRI - Enable Timer Interrupt A write to 1 will enable timer interrupt.
- 57 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 6:
Legacy IR Mode: Not used. A read will return 0. MIR, FIR mode: EFSFI - Enable Frame Status FIFO Interrupt A write to 1 will enable frame status FIFO interrupt.
Advanced SIR/ASK-IR, Remote IR: Not used.
Bit 5:
Legacy IR Mode: Not used. A read will return 0. Advanced SIR/ASK-IR, MIR, FIR, Remote IR: ETXTHI - Enable Transmitter Threshold Interrupt A write to 1 will enable transmitter threshold interrupt.
Bit 4:
Legacy IR Mode: Not used. A read will return 0. MIR, FIR, Remote IR: EDMAI - Enable DMA Interrupt. A write to 1 will enable DMA interrupt.
Bit 3: Bit 2:
Reserved. A read will return 0. Legacy IR Mode: EUSRI - Enable USR (IR Status Register) Interrupt A write to 1 will enable IR status register interrupt. Advanced SIR/ASK-IR: EUSRI - Enable USR (IR Status Register) Interrupt A write to 1 will enable IR status register interrupt. MIR, FIR, Remote Controller: EHSRI/ETXURI - Enable USR Interrupt or Enable Transmitter Underrun Interrupt A write to 1 will enable USR interrupt or enable transmitter underrun interrupt.
Bit 1: Bit 0:
ETBREI - Enable TBR (Transmitter Buffer Register) Empty Interrupt A write to 1 will enable the transmitter buffer register empty interrupt. ERBRI - Enable RBR (Receiver Buffer Register) Interrupt A write to 1 will enable receiver buffer register interrupt.
- 58 -
W83L517D/W83L517D-F
8.2.3 Set0.Reg2 - Interrupt Status Register/IR FIFO Control Register (ISR/UFR)
B7 B6 B5 B4 B3 B2 B1 B0
Interrupt Status Register (Read Only)
MODE
Legacy IR Advanced IR
Reset Value
FIFO Enable FIFO Enable TMR_I 0 FSF_I 0
0
0
IID2 HS_I 0
IID1 USR_I/ FEND_I 0
IID0
IP
TXTH_I DMA_I 1 0
TXEMP_I RXTH_I 1 0
Legacy IR:
This register reflects the Legacy IR interrupt status, which is encoded by different interrupt sources into 3 bits. Bit 7, 6: Bit 5, 4: These two bits are set to a logical 1 when UFR bit 0 = 1. These two bits are always logical 0.
Bit 3: When not in FIFO mode, this bit is always 0. In FIFO mode, both bit 3 and 2 are set to logical 1 when a time-out interrupt is pending. Bit 2, 1: below. These bits identify the priority level of the pending interrupt, as shown in the table
Bit 0: This bit is a logical 1 if there is no interrupt pending. If one of the interrupt sources has occurred, this bit will be set to logical 0. TABLE: INTERRUPT CONTROL FUNCTION
ISR INTERRUPT SET AND FUNCTION
Bit 3 0 0
Bit 2 0 1
Bit 1 0 1
Bit 0 1 0
Interrupt priority First
Interrupt Type IR Receive Status RBR Data Ready
Interrupt Source No Interrupt pending 1. OER = 1 2. PBER =1 3. NSER = 1 4. SBD = 1 1. RBR data ready 2. FIFO interrupt active level reached Data present in RX FIFO for 4 characters period of time since last access of RX FIFO.
Clear Interrupt Read USR 1. Read RBR 2. Read RBR until FIFO data under active level Read RBR 1. Write data into TBR 2. Read ISR (if priority is third)
0
1
0
0
Second
1
1
0
0
Second
FIFO Data Time-out
0
0
1
0
Third
TBR Empty
TBR empty
** Bit 3 of ISR is enabled when bit 0 of UFR is a logical 1.
- 59 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Advanced IR:
Bit 7: TMR_I - Timer Interrupt. Set to 1 when timer counts to logical 0. This bit is valid when: (1) the timer registers are defined in Set4.Reg0 and Set4.Reg1; (2) EN_TMR(Enable Timer, in Set4.Reg2.Bit0) is set to 1; (3) ENTMR_I (Enable Timer Interrupt, in Set0.Reg1.Bit7) is set to 1. Bit 6: MIR, FIR modes: FSF_I - Frame Status FIFO Interrupt. Set to 1 when Frame Status FIFO is equal or larger than the threshold level or Frame Status FIFO time-out occurs. Cleared to 0 when Frame Status FIFO is below the threshold level. Advanced SIR/ASK-IR, Remote IR modes: Not used. Bit 5: TXTH_I - Transmitter Threshold Interrupt. Set to 1 if the TBR (Transmitter Buffer Register) FIFO is below the threshold level. Cleared to 0 if the TBR (Transmitter Buffer Register) FIFO is above the threshold level. Bit 4: MIR, FIR, Remote IR Modes: DMA_I - DMA Interrupt. Set to 1 if the DMA controller 8237A sends a TC (Terminal Count) to I/O device which might be a Transmitter TC or a Receiver TC. Cleared to 0 when this register is read. Bit 3: HS_I - Handshake Status Interrupt. Set to 1 when the Handshake Status Register has a toggle. Cleared to 0 when Handshake Status Register (HSR) is read. Note that in all IR modes including SIR, ASKIR, MIR, FIR, and Remote Control IR, this bit defaults to be inactive unless IR Handshake Status Enable (IRHS_EN) is set to 1. Bit 2: Advanced SIR/ASK-IR modes: USR_I - IR Status Interrupt. Set to 1 when overrun error, parity error, stop bit error, or silent byte error is detected and registered in the IR Status Register (USR). Cleared to 0 when USR is read. MIR, FIR modes: FEND_I - Frame End Interrupt. Set to 1 when (1) a frame has a grace end to be detected where the frame signal is defined in the physical layer of IrDA version 1.1; (2) abort signal or illegal signal has been detected during receiving valid data. Cleared to 0 when this register is read. Remote Controller Mode: Not used. Bit 1: TXEMP_I - Transmitter Empty. Set to 1 when transmitter (or, say, FIFO + Transmitter) is empty. Cleared to 0 when this register is read. Bit 0: RXTH_I - Receiver Threshold Interrupt. Set to 1 when (1) the Receiver Buffer Register (RBR) is equal or larger than the threshold level; or (2) RBR time-out occurs if the receiver buffer register has valid data and isbelow the threshold level. Cleared to 0 when RBR is less than threshold level after reading RBR.
- 60 -
W83L517D/W83L517D-F
IR FIFO Control Register (UFR):
MODE BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
Legacy IR Advanced IR
Reset Value
RXFTL1 (MSB) RXFTL1 (MSB) 0
RXFTL0 (LSB)
0
0
0 0 0
TXF_RST RXF_RST EN_FIFO TXF_RST RXF_RST EN_FIFO 0 0 0
RXFTL0 TXFTL1 TXFTL0 (LSB) (MSB) (LSB) 0 0 0
Legacy IR:
This register is used to control FIFO functions of the IR. Bit 6, 7: These two bits are used to set the active level for the receiver FIFO interrupt. For example, if the interrupt active level is set as 4 bytes and there are more than 4 data characters in the receiver FIFO, the interrupt will be activated to notify CPU to read the data from FIFO. TABLE: FIFO TRIGGER LEVEL
BIT 7 BIT 6 RX FIFO INTERRUPT ACTIVE LEVEL (BYTES)
0 0 1 1 Bit 4, 5:
0 1 0 1 Reserved
01 04 08 14
Bit 3: When this bit is programmed to logic 1, the DMA mode will change from mode 0 to mode 1 if UFR bit 0 = 1. Bit 2: Setting this bit to a logical 1 resets the TX FIFO counter logic to its initial state. This bit will be cleared to logical 0 by itself after being set to logical 1. Bit 1: Setting this bit to logical 1 resets the RX FIFO counter logic to its initial state. This bit will be cleared to a logical 0 by itself after being set to logical 1. Bit 0: This bit enables the 16550 (FIFO) mode of the IR. This bit should be set to logical 1 before other bits of UFR can be programmed.
Advanced IR:
BIT 7, 6: RXFTL1, 0 - RECEIVER FIFO THRESHOLD LEVEL
Its definition is the same as Legacy IR. RXTH_I becomes 1 when the Receiver FIFO Threshold Level is equal to or larger than the defined value shown as follow.
- 61 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
RXFTL1, 0 (BIT 7, 6)
RX FIFO THRESHOLD LEVEL (FIFO SIZE: 16-BYTE)
RX FIFO THRESHOLD LEVEL (FIFO SIZE: 32-BYTE)
00 01 10 11
1 4 8 14 Note that the FIFO Size is selectable in SET2.Reg4.
1 4 16 26
Bit 5, 4:
TXFTL1, 0 - Transmitter FIFO Threshold Level TXTH_I (Transmitter Threshold Level Interrupt) is set to 1 when the Transmitter Threshold Level is less than the programmed value shown below.
TX FIFO THRESHOLD LEVEL (FIFO SIZE: 16-BYTE) TX FIFO THRESHOLD LEVEL (FIFO SIZE: 32-BYTE)
TXFTL1, 0 (BIT 5, 4)
00 01 10 11
1 3 9 13
1 7 17 25
Bit 3 ~0
Same as in Legacy IR Mode
8.2.4
Set0.Reg3 - IR Control Register/Set Select Register (UCR/SSR):
These two registers share the same address. In all Register Sets, Set Select Register (SSR) can be programmed to select a desired Set, but IR Control Register can only be programmed in Set 0 and Set 1. In other words, writing to Reg3 in Sets other than Set 0 and Set 1 will not affect IR Control Register. The mapping of entry Set and programming value is shown below.
- 62 -
W83L517D/W83L517D-F
SSR BITS
SELECTED
7 0 1 1 1 1 1 1 1
6
x
5
x
4
x
3
x
2
x
1
x
0
x
Hex Value
Set Set 0 Set1 Set 2 Set 3 Set 4 Set 5 Set 6 Set 7
Any combination except those used in SET 2~7 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 1 1 1 0 0 1 1 0 0 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0
0xE0 0xE4 0xE8 0xEC 0xF0 0xF4
8.2.5
Set0.Reg4 - Handshake Control Register (HCR)
B7 B6 B5 B4 B3 B2 B1 B0
MODE
Legacy IR
Reset Value
0 0
0 1
0 1
XLOOP 0
EN_IRQ TX_WT 0
0 EN_DMA 0
0 0 0
0 0 0
Advanced IR AD_MD2 AD_MD1 AD_MD0 SIR_PLS
Legacy IR Register:
This register controls the pins of IR used for handshaking with peripherals such as modem, and controls the diagnostic mode of IR. Bit 4: When this bit is set to logical 1, the legacy IR enters diagnostic mode by an internal loopback: IRTX is forced to logical 0, and IRRX is isolated from the communication link instead of the TSR. Bit 3: The legacy IR interrupt output is enabled by setting this bit to logic 1.
Advanced IR Register:
Bit 7~5 Advanced SIR/ASK-IR, MIR, FIR, Remote Controller Modes: AD_MD2~0 - Advanced IR/Infrared Mode Select. These registers are active when Advanced IR Select (ADV_SL, in Set2.Reg2.Bit0) is set to 1. Operational mode selection is defined as follows. When backward operation occurs, these registers will be reset to 0 and fall back to legacy IR mode.
- 63 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
AD_MD2~0 (BIT 7, 6, 5)
SELECTED MODE
000 001 010 011 100 101 110 111 Bit 4: MIR, FIR Modes: SIR_PLS - Send Infrared Pulse
Reserved Low speed MIR (0.576M bps) Advanced ASK-IR Advanced SIR High Speed MIR (1.152M bps) FIR (4M bps) Consumer IR Reserved
Writing 1 to this bit will send a 2 s long infrared pulse after physical frame end. This is to signal to SIR that the high speed infrared is still in. This bit will be auto cleared by hardware. Other Modes: Not used. Bit 3: MIR, FIR modes: TX_WT - Transmission Waiting If this bit is set to 1, the transmitter will wait for TX FIFO to reach threshold level or transmitter time-out before it begins to transmit data; this prevents short queues of data bytes from transmitting prematurely. This is to avoid Underrun. Other Modes: Not used. Bit 2: MIR, FIR modes: EN_DMA - Enable DMA Enable DMA function for transmitting or receiving. Before using this, the DMA channel should be selected first. If only RX DMA channel is set and TX DMA channel is disabled, then the single DMA channel is used. In the single channel system, the bit of D_CHSW (DMA channel swap, in Set 2.Reg2.Bit3) will determine if it is RX_DMA or TX_DMA channel. Other modes: Not used. Bit 1, 0: RTS, DTR Functional definitions are the same as in legacy IR mode.
- 64 -
W83L517D/W83L517D-F
8.2.6 Set0.Reg5 - IR Status Register (USR)
B7 B6 B5 B4 B3 B2 B1 B0
MODE
Legacy IR
Reset Value
RFEI 0
TSRE TSRE 0
TBRE TBRE 0
SBD 0
NSER 0
PBER 0
OER OER 0
RDR RDR 0
Advanced IR LB_INFR
MX_LEX PHY_ERR CRC_ERR
Legacy IR Register: These registers are defined the same as previous description. Advanced IR Register: Bit 7: MIR, FIR Modes: LB_INFR - Last Byte In Frame End Set to 1 when last byte of a frame is in the bottom of FIFO. This bit separates one frame from another when RX FIFO has more than one frame. Bit 6, 5: Bit 4: Same as legacy IR description. MIR, FIR modes: MX_LEX - Maximum Frame Length Exceed Set to 1 when the length of a frame from the receiver has exceeded the programmed frame length defined in SET4.Reg6 and Reg5. If this bit is set to 1, the receiver will not receive any data to RX FIFO. Bit 3: MIR, FIR modes: PHY_ERR - Physical Layer Error Set to 1 when an illegal data symbol is received. The illegal data symbol is defined in physical layer of IrDA version 1.1. When this bit is set to 1, the decoder of receiver will be aborted and a frame end signal is set to 1. Bit 2: MIR, FIR Modes: CRC_ERR - CRC Error Set to 1 when an attached CRC is erroneous. Bit 1, 0: OER - Overrun Error, RDR - RBR Data Ready Definitions are the same as legacy IR.
- 65 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
8.2.7 Set0.Reg6 - Reserved
Set0.Reg7 - User Defined Register (UDR/AUDR)
MODE BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
Legacy IR
Bit 7
Bit 6 UNDRN 0
Bit 5 RX_BSY/ RX_IP 0
Bit 4 LST_FE/ RX_PD 0
Bit 3 S_FEND 0
Bit 2 0 0
Bit 1 LB_SF 0
Bit 0 RX_TO 0
Advanced FLC_ACT IR
Reset Value
0
Legacy IR Register: This is a temporary register that can be accessed and defined by the user. Advanced IR Register: Bit 7 MIR, FIR Modes: FLC_ACT - Flow Control Active Set to 1 when the flow control occurs. Cleared to 0 when this register is read. Note that this will be affected by Set5.Reg2 which controls the SIR mode switches to MIR/FIR mode or MIR/FIR mode operated in DMA function switches to SIR mode. Bit 6 MIR, FIR Modes: UNDRN - Underrun Set to 1 when transmitter is empty and S_FEND (bit 3 of this register) is not set in PIO mode or no TC (Terminal Count) in DMA mode. Cleared to 0 after a write to 1. Bit 5 MIR, FIR Modes: RX_BSY - Receiver Busy Set to 1 when receiver is busy or active in process. Remote IR mode: RX_IP - Receiver in Process Set to 1 when receiver is in process. Bit 4: MIR, FIR modes: LST_FE - Lost Frame End Set to 1 when a frame end in a entire frame is lost. Cleared to 0 when this register is read. Remote IR Modes: RX_PD - Receiver Pulse Detected Set to 1 when one or more remote pulses are detected. Cleared to 0 when this register is read.
- 66 -
W83L517D/W83L517D-F
Bit 3
MIR, FIR Modes: S_FEND - Set a Frame End Set to 1 when trying to terminate the frame, that is, the procedure od PIO command is An Entire Frame = Write Frame Data (First) + Write S_FEND (Last) This bit should be set to 1, if used in PIO mode, to avoid transmitter underrun. Note that setting S_FEND to 1 is equivalent to TC (Terminal Count) in DMA mode. Therefore, this bit should be set to 0 in DMA mode.
Bit 2: Bit 1:
Reserved. MIR, FIR Modes: LB_SF - Last Byte Stay in FIFO A 1 in this bit indicates one or more frame ends remain in receiver FIFO.
Bit 0:
MIR, FIR, Remote IR Modes: RX_TO - Receiver FIFO or Frame Status FIFO time-out Set to 1 when receiver FIFO or frame status FIFO time-out occurs
8.3
Set1 - Legacy Baud Rate Divisor Register
REGISTER NAME REGISTER DESCRIPTION
ADDRESS OFFSET
0 1 2 3 4 5 6 7
BLL BHL ISR/UFR UCR/SSR HCR USR HSR UDR/ESCR
Baud Rate Divisor Latch (Low Byte) Baud Rate Divisor Latch (High Byte) Interrupt Status or IR FIFO Control Register IR Control or Sets Select Register Handshake Control Register IR Status Register Handshake Status Register User Defined Register
8.3.1
Set1.Reg0~1 - Baud Rate Divisor Latch (BLL/BHL)
These two registers of BLL and BHL are baud rate divisor latch in the legacy SIR/ASK-IR mode. Accessing these registers in Advanced IR mode will cause backward operation, that is, UART will fall back to legacy SIR mode and clear some register values as shown in the following table.
SET & REGISTER ADVANCED MODE DIS_BACK=x LEGACY MODE DIS_BACK=0
Set 0.Reg 4 Set 2.Reg 2 Set 4.Reg 3
Bit 7~5 Bit 0, 5, 7 Bit 2, 3
Bit 5, 7 -
Note that DIS_BACK=1 (Disable Backward operation) in legacy SIR/ASK-IR mode will not affect any register which is meaningful in legacy SIR/ASK-IR.
- 67 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
8.3.2 Set1.Reg 2~7
These registers are defined the same as Set 0 registers.
8.4
Set2 - Interrupt Status or IR FIFO Control Register (ISR/UFR)
Register Name ABLL ABHL ADCR1 SSR ADCR2 Reserved TXFDTH RXFDTH Register Description Advanced Baud Rate Divisor Latch (Low Byte) Advanced Baud Rate Divisor Latch (High Byte) Advanced IR Control Register 1 Sets Select Register Advanced IR Control Register 2 Transmitter FIFO Depth Receiver FIFO Depth
These registers are only used in advanced modes. Address Offset 0 1 2 3 4 5 6 7
8.4.1
Reg0, 1 - Advanced Baud Rate Divisor Latch (ABLL/ABHL)
These two registers are the same as legacy IR baud rate divisor latch in SET 1.Reg0~1. In advanced SIR/ASK-IR mode, the user should program these registers to set baud rate. This is to prevent backward operations from occurring.
8.4.2
Reg2 - Advanced IR Control Register 1 (ADCR1)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
MODE
Advanced IR BR_OUT
Reset Value
0
EN_LOU T 0
ALOOP D_CHSW DMATHL 0 0 0
DMA_F 0
ADV_SL 0
0
Bit 7:
BR_OUT - Baud Rate Clock Output When written to 1, the programmed baud rate clock will be output to DTR pin. This bit is only used to test baud rate divisor.
Bit 6: Bit 5:
Reserved, write 0. EN_LOUT - Enable Loopback Output A write to 1 will enable transmitter to output data to IRTX pin when loopback operation occurs. Internal data can be verified through an output pin by setting this bit.
- 68 -
W83L517D/W83L517D-F
Bit 4: Bit 3:
ALOOP - All Mode Loopback A write to 1 will enable loopback in all modes. D_CHSW - DMA TX/RX Channel Swap If only one DMA channel operates in MIR/FIR mode, then the DMA channel can be swapped. D_CHSW 0 1 A write to 1 will enable output data when ALOOP=1. DMA Channel Selected Receiver (Default) Transmitter
Bit 2:
DMATHL - DMA Threshold Level Set DMA threshold level as shown in the following table.
DMATHL TX FIFO THRESHOLD RX FIFO THRESHOLD
16-Byte 0 1 Bit 1: DMA_F - DMA Fairness DMA_F 0 1 Bit 0: ADV_SL - Advanced Mode Select A write to 1 selects advanced mode. 13 23
32-Byte 13 7
(16/32-Byte) 4 10
Function Description DMA request (DREQ) is forced inactive after 10.5us No effect DMA request.
8.4.3
Reg3 - Sets Select Register (SSR)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
Reading this register returns E0H. Writing a value selects Register Set.
REG.
SSR
Refault Value
SSR7 1
SSR6 1
SSR5 1
SSR4 0
SSR3 0
SSR2 0
SRR1 0
SRR0 0
- 69 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
8.4.4 Reg4 - Advanced IR Control Register 2 (ADCR2)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
MODE
Advanced IR DIS_BACK Reset Value Bit 7: 0
0
PR_DIV1 PR_DIV0 RX_FSZ1 RX_FSZ0 TX_FSZ1 TXFSZ0 0 0 0 0 0 0
DIS_BACK - Disable Backward Operation A write to 1 disables backward legacy IR mode. When operating in legacy SIR/ASK-IR mode, this bit should be set to 1 to avoid backward operation.
Bit 6: Bit 5, 4:
Reserved, write 0. PR_DIV1~0 - Pre-Divisor 1~0. These bits select pre-divisor for external input clock 24M Hz. The clock goes through the pre-divisor then input to baud rate divisor of IR.
PR_DIV1~0 PRE-DIVISOR MAX. BAUD RATE
00 01 10 11 Bit 3, 2:
13.0 1.625 6.5 1
115.2K bps 921.6K bps 230.4K bps 1.5M bps
RX_FSZ1~0 - Receiver FIFO Size 1~0 These bits setup receiver FIFO size when FIFO is enable.
RX_FSZ1~0 RX FIFO SIZE
00 01 1X Bit 1, 0: TX_FSZ1~0 - Transmitter FIFO Size 1~0
16-Byte 32-Byte Reserved
These bits setup transmitter FIFO size when FIFO is enable.
TX_FSZ1~0 TX FIFO SIZE
00 01 1X
16-Byte 32-Byte Reserved
- 70 -
W83L517D/W83L517D-F
TABLE: SIR Baud Rate
BAUD RATE FROM DIFFERENT PRE-DIVIDER
Pre-Div: 13 1.8461M Hz 50 75 110 134.5 150 300 600 1200 1800 2000 2400 3600 4800 7200 9600 19200 38400 57600 115200
Pre-Div:1.625 14.769M Hz 400 600 880 1076 1200 2400 4800 9600 14400 16000 19200 28800 38400 57600 76800 153600 307200 460800 921600
Pre-Div: 1.0 24M Hz 650 975 1430 1478.5 1950 3900 7800 15600 23400 26000 31200 46800 62400 93600 124800 249600 499200 748800 1497600
Decimal divisor used to generate 16X clock 2304 1536 1047 857 768 384 192 96 64 58 48 32 24 16 12 6 3 2 1
Error Percentage between desired and actual ** ** 0.18% 0.099% ** ** ** ** ** 0.53% ** ** ** ** ** ** ** ** **
** The percentage error for all baud rates, except where indicated otherwise, is 0.16%.
- 71 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
8.4.5 Reg6 - Transmitter FIFO Depth (TXFDTH) (Read Only)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
MODE
Advanced IR
Reset Value
0 0
0 0
TXFD5 0
TXFD4 0
TXFD3 0
TXFD2 0
TXFD1 0
TXFD1 0
Bit 7~6: Bit 5~0:
Reserved, Read 0. Reading these bits returns the current transmitter FIFO depth, that is, the number of bytes left in the transmitter FIFO.
8.4.6
Reg7 - Receiver FIFO Depth (RXFDTH) (Read Only)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
MODE
Advanced IR
Reset Value
0 0
0 0
RXFD5 0
RXFD4 0
RXFD3 0
RXFD2 0
RXFD1 0
RXFD1 0
Bit 7~6: Bit 5~0:
Reserved, Read 0. Reading these bits returns the current receiver FIFO depth, that is, the number of bytes left in the receiver FIFO.
8.5
Set3 - Version ID and Mapped Control Registers
REGISTER NAME REGISTER DESCRIPTION
ADDRESS OFFSET
0 1 2 3 4 5 6 7
AUID MP_UCR MP_UFR SSR Reversed Reserved Reserved Reserved
Advanced IR ID Mapped IR Control Register Mapped IR FIFO Control Register Sets Select Register -
8.5.1
Reg0 - Advanced IR ID (AUID)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
This register is read only. It stores advanced IR version ID. Reading it returns 1XH.
REG.
SSR Default Value
SSR7 0
SSR6 0
SSR5 0
SSR4 1
SSR3 X
SSR2 X
SRR1 X
SRR0 X
- 72 -
W83L517D/W83L517D-F
8.5.2 Reg1 - Mapped IR Control Register (MP_UCR)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
This register is read only. Reading this register returns IR Control Register value of Set 0.
REG.
SSR
Default Value
SSR7 0
SSR6 0
SSR5 0
SSR4 0
SSR3 0
SSR2 0
SRR1 0
SRR0 0
8.5.3
Reg2 - Mapped IR FIFO Control Register (MP_UFR)
This register is read only. Reading this register returns IR FIFO Control Register (UFR) value of SET 0.
REG. BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
SSR
Default Value
SSR7 0
SSR6 0
SSR5 0
SSR4 0
SSR3 0
SSR2 0
SRR1 0
SRR0 0
8.5.4
Reg3 - Sets Select Register (SSR)
Bit 7 SSR7 1 Bit 6 SSR6 1 Bit 5 SSR5 1 Bit 4 SSR4 0 Bit 3 SSR3 0 Bit 2 SSR2 1 Bit 1 SRR1 0 Bit 0 SRR0 0
Reading this register returns E4H. Writing a value selects a Register Set. Reg. SSR
Default Value
8.6
Set4 - TX/RX/Timer counter registers and IR control registers.
REGISTER NAME REGISTER DESCRIPTION
ADDRESS OFFSET
0 1 2 3 4 5 6 7
TMRL TMRH IR_MSL SSR TFRLL TFRLH RFRLL RFRLH
Timer Value Low Byte Timer Value High Byte Infrared Mode Select Sets Select Register Transmitter Frame Length Low Byte Transmitter Frame Length High Byte Receiver Frame Length Low Byte Receiver Frame Length High Byte
- 73 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
8.6.1 Set4.Reg0, 1 - Timer Value Register (TMRL/TMRH)
This is a 12-bit timer whose resolution is 1ms, that is, the maximum programmable time is 212-1 ms. The timer is a down-counter and starts counting down when EN_TMR (Enable Timer) of Set4.Reg2 is set to 1. When the timer counts down to zero and EN_TMR=1, the TMR_I is set to 1 and a new initial value will be loaded into counter.
8.6.2
Set4.Reg2 - Infrared Mode Select (IR_MSL)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
MODE
Advanced IR
Reset Value
0
0
0
0
IR_MSL1 0
IR_MSL0 0
TMR_TST 0
EN_TMR 0
Bit 7~4: Reserved, write to 0. Bit 3, 2: IR_MSL1, 0 - Infrared Mode Select Select legacy IR, SIR, or ASK-IR mode. Note that in legacy SIR/ASK-IR user should set DIS_BACK=1 to avoid backward when programming baud rate. IR_MSL1, 0 00 01 10 11 Bit 1: TMR_TST - Timer Test When set to 1, reading the TMRL/TMRH returns the programmed values of TMRL/TMRH instead of the value of down counter. This bit is for testing timer register. Bit 0: EN_TMR - Enable Timer A write to 1 will enable the timer. Operation Mode Selected Legacy IR CIR Legacy ASK-IR Legacy SIR
8.6.3
Set4.Reg3 - Set Select Register (SSR)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
Reading this register returns E8H. Writing this register selects Register Set.
REG.
SSR
Default Value
SSR7 1
SSR6 1
SSR5 1
SSR4 1
SSR3 1
SSR2 0
SRR1 0
SRR0 0
- 74 -
W83L517D/W83L517D-F
8.6.4 Set4.Reg4, 5 - Transmitter Frame Length (TFRLL/TFRLH)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
REG.
TFRLL
Reset Value
bit 7 0 -
bit 6 0 -
bit 5 0 -
bit 4 0 bit 12 0
bit3 0 bit 11 0
bit 2 0 bit 10 0
bit 1 0 bit 9 0
bit 0 0 bit 8 0
TFRLH
Reset Value
These are combined to be a 13-bit register. Writing these registers programs the transmitter frame length of a package. These registers are only valid when APM=1 (automatic package mode, Set5.Reg4.bit5). When APM=1, the physical layer will split data stream to a programmed frame length if the transmitted data is larger than the programmed frame length. When these registers are read, they will return the number of bytes which is not transmitted from a frame length programmed.
8.6.5
Set4.Reg6, 7 - Receiver Frame Length (RFRLL/RFRLH)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
REG.
RFRLL
Reset Value
bit 7 0 -
bit 6 0 -
bit 5 0 -
bit 4 0 bit 12 0
bit 3 0 bit 11 0
bit 2 0 bit 10 0
bit 1 0 bit 9 0
bit 0 0 bit 8 0
RFRLH
Reset Value
These are combined to be a 13-bit register and up counter. The length of receiver frame will be limited to the programmed frame length. If the received frame length is larger than the programmed receiver frame length, the bit of MX_LEX (Maximum Length Exceed) will be set to 1. Simultaneously, the receiver will not receive any more data to RX FIFO until the next start flag of the next frame, which is defined in the physical layer IrDA 1.1. Reading these registers returns the number of received data bytes of a frame from the receiver.
8.7
Set 5 - Flow control and IR control and Frame Status FIFO registers
REGISTER NAME REGISTER DESCRIPTION
ADDRESS OFFSET
0 1 2 3 4 5 6 7
FCBLL FCBHL FC_MD SSR IRCFG1 FS_FO RFRLFL RFRLFH
Flow Control Baud Rate Divisor Latch Register (Low Byte) Flow Control Baud Rate Divisor Latch Register (High Byte) Flow Control Mode Operation Sets Select Register Infrared Configure Register Frame Status FIFO Register Receiver Frame Length FIFO Low Byte Receiver Frame Length FIFO High Byte
- 75 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
8.7.1 Set5.Reg0, 1 - Flow Control Baud Rate Divisor Latch Register (FCDLL/ FCDHL)
If flow control is enforced when UART switches mode from MIR/FIR to SIR, then the pre-programmed baud rate of FCBLL/FCBHL are loaded into advanced baud rate divisor latch (ADBLL/ADBHL).
8.7.2
Set5.Reg2 - Flow Control Mode Operation (FC_MD)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
These registers control flow control mode operation as shown in the following table.
REG.
FC_MD Reset Value Bit 7~5
FC_MD2 0
FC_MD1 0
FC_MD0 0
0
FC_DSW 0
EN_FD 0
EN_BRFC 0
EN_FC 0
FC_MD2 - Flow Control Mode When flow control is enforced, these bits will be loaded into AD_MD2~0 of advanced HSR (Handshake Status Register). These three bits are defined as same as AD_MD2~0.
Bit 4: Bit 3:
Reserved, write 0. FC_DSW - Flow Control DMA Channel Swap A write to 1 allows user to swap DMA channel for transmitter or receiver when flow control is enforced. FC_DSW 0 1 Next Mode After Flow Control Occurred Receiver Channel Transmitter Channel
Bit 2: Bit 1:
EN_FD - Enable Flow DMA Control A write to 1 enables UART to use DMA channel when flow control is enforced. EN_BRFC - Enable Baud Rate Flow Control A write to 1 enables FC_BLL/FC_BHL (Flow Control Baud Rate Divider Latch, in Set5.Reg1~0) to be loaded into advanced baud rate divisor latch (ADBLL/ADBHL, in Set2.Reg1~0).
Bit 0:
EN_FC - Enable Flow Control A write to 1 enables flow control function and bit 7~1 of this register.
8.7.3
Set5.Reg3 - Sets Select Register (SSR)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
Writing this register selects Register Set. Reading this register returns ECH.
REG.
SSR
Default Value
SSR7 1
SSR6 1
SSR5 1
SSR4 0
SSR3 1
SSR2 1
SRR1 0
SRR0 0
- 76 -
W83L517D/W83L517D-F
8.7.4 Set5.Reg4 - Infrared Configure Register 1 (IRCFG1)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
REG.
IRCFG1
Reset Value
0
FSF_TH 0
FEND_M AUX_RX 0 0
0
0
IRHSSL 0
IR_FULL 0
Bit 7: Bit 6:
Reserved, write 0. FSF_TH - Frame Status FIFO Threshold Set this bit to determine the frame status FIFO threshold level and to generate the FSF_I. The threshold level values are defined as follows.
FSF_TH STATUS FIFO THRESHOLD LEVEL
0 1
BIT 5: FEND_MD - FRAME END MODE
2 4
A write to 1 enables hardware to split data stream into equal length frame automatically as defined in Set4.Reg4 and Set4.Reg5, i.e., TFRLL/TFRLH. Bit 4: Bit 3~2: Bit 1: AUX_RX - Auxiliary Receiver Pin A write to 1 selects IRRX input pin. (Refer to Set7.Reg7.Bit5) Reserved, write 0. IRHSSL - Infrared Handshake Status Select When set to 0, the HSR (Handshake Status Register) operates the same as defined in IR mode. A write to 1 will disable HSR, and reading HSR returns 30H. Bit 0: IR_FULL - Infrared Full Duplex Operation When set to 0, IR module operates in half duplex. A write to 1 makes IR module operate in full duplex.
8.7.5
Set5.Reg5 - Frame Status FIFO Register (FS_FO)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
This register shows the bottom byte of frame status FIFO.
REG.
FS_FO
Reset Value
FSFDR 0
LST_FR 0
0
MX_LEX PHY_ERR 0 0
CRC_ER R 0
RX_OV 0
FSF_OV 0
- 77 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 7: Bit 6: Bit 5: Bit 4:
FSFDR - Frame Status FIFO Data Ready Indicates that a data byte is valid in frame status FIFO bottom. LST_FR - Lost Frame Set to 1 when one or more frames have been lost. Reserved. MX_LEX - Maximum Frame Length Exceed Set to 1 when incoming data exceeds programmed maximum frame length defined in Set4.Reg6 and Set4.Reg7. This bit is in frame status FIFO bottom and is valid only when FSFDR=1 (Frame Status FIFO Data Ready).
Bit 3:
PHY_ERR - Physical Error When receiving data, any physical layer error as defined in IrDA 1.1 will set this bit to 1. This bit is in frame status FIFO bottom and is valid only when FSFDR=1 (Frame Status FIFO Data Ready).
Bit 2:
CRC_ERR - CRC Error Set to 1 when a bad CRC is received in a frame. This CRC belongs to physical layer as defined in IrDA 1.1. This bit is in frame status FIFO bottom and is valid only when FSFDR=1 (Frame Status FIFO Data Ready).
Bit 1: Bit 0:
RX_OV - Received Data Overrun Set to 1 when receiver FIFO overruns. FSF_OV - Frame Status FIFO Overrun Set to 1 When frame status FIFO overruns.
8.7.6
Set5.Reg6, 7 - Receiver Frame Length FIFO (RFLFL/RFLFH) or Lost Frame Number (LST_NU)
REG. BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
RFLFL/ LST_NU
Reset Value
Bit 7 0 0
Bit 6 0 0
Bit 5 0 0
Bit 4 0 Bit 12 0
Bit 3 0 Bit 11 0
Bit 2 0 Bit 10 0
Bit 1 0 Bit 9 0
Bit 0 0 Bit 8 0
RFLFH
Reset Value
Receiver Frame Length FIFO (RFLFL/RFLFH):
These are combined to be a 13-bit register. Reading these registers returns received byte count for the frame. When read, the register of RFLFH will pop-up another frame status and frame length if FSFDR=1 (Set5.Reg4.Bit7).
Lost Frame Number (LST_NU):
When LST_FR=1 (Set5.Reg4.Bit6), Reg6 stands for LST_NU which is a 8-bit register holding the number of frames lost in succession.
- 78 -
W83L517D/W83L517D-F
8.8 Set6 - IR Physical Layer Control Registers
REGISTER NAME REGISTER DESCRIPTION
ADDRESS OFFSET
0 1 2 3 4 5 6 7
IR_CFG2 MIR_PW SIR_PW SSR HIR_FNU IR_ID1 IR_ID2 HIR_SL
Infrared Configure Register 2 MIR (1.152M bps or 0.576M bps) Pulse Width SIR Pulse Width Sets Select Register High Speed Infrared Flag Number IR ID Register 1 IR ID Register 2 High Speed infrared Select Register
8.8.1
Set6.Reg0 - Infrared Configure Register 2 (IR_CFG2)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
This register controls ASK-IR, MIR, FIR operations.
REG.
IR_CFG2 SHMD_N SHDM_N FIR_CRC MIR_CRC
Reset Value
0
INV_CRC DIS_CRC 0 0
0
0
0
1
0
Bit 7:
SHMD_N - ASK-IR Modulation Disable SHMD_N 0 1 Modulation Mode IRTX modulate 500K Hz Square Wave Re-rout IRTX Demodulation Mode Demodulation 500K Hz Re-rout IRRX CRC Type 16-bit CRC 32-bit CRC
Bit 6:
SHDM_N - ASK-IR Demodulation Disable SHDM_N 0 1
Bit 5:
FIR_CRC - FIR (4M bps) CRC Type FIR_CRC 0 1
Note that the 16/32-bit CRC are defined in IrDA 1.1 physical layer. Bit 4: MIR_CRC - MIR (1.152M/0.576M bps) CRC Type MIR_CRC 0 1 CRC Type 16-bit CRC 32-bit CRC
- 79 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 2: Bit 1: Bit 0: INV_CRC - Inverting CRC When set to 1, the CRC is inversely output in physical layer. DIS_CRC - Disable CRC When set to 1, the transmitter does not transmit CRC in physical layer. Reserved, write 1.
8.8.2
Set6.Reg1 - MIR (1.152M/0.576M bps) Pulse Width
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
REG.
MIR_PW
Reset Value
0
0
0
M_PW4 0
M_PW3 1
M_PW2 0
M_PW1 1
M_PW0 0
This 5-bit register sets MIR output pulse width.
M_PW4~0 MIR PULSE WIDTH (1.152M BPS) MIR OUTPUT WIDTH (0.576M BPS)
00000 00001 00010
...
0 ns 20.83 ns 41.66 (==20.83*2) ns
...
0 ns 41.66 ns 83.32 (==41.66*2) ns
...
k10
...
20.83*k10 ns
...
41.66*k10 ns
...
11111
645 ns
1290 ns
8.8.3
Set6.Reg2 - SIR Pulse Width
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
REG.
SIR_PW
Reset Value
0
0
0
S_PW4 0
S_PW3 0
S_PW2 0
S_PW1 0
S_PW0 0
This 5-bit register sets SIR output pulse width.
S_PW4~0 SIR OUTPUT PULSE WIDTH
00000 01101 Others
3/16 bit time of IR 1.6 us 1.6 us
- 80 -
W83L517D/W83L517D-F
8.8.4 Set6.Reg3 - Set Select Register
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
Select Register Set by writing a set number to this register. Reading this register returns F0H.
REG.
SSR
Default Value
SSR7 1
SSR6 1
SSR5 1
SSR4 1
SSR3 0
SSR2 0
SRR1 0
SRR0 0
8.8.5
Set6.Reg4 - High Speed Infrared Beginning Flag Number (HIR_FNU)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
REG.
HIR_FNU
Reset Value
M_FG3 0
M_FG2 0
M_FG1 1
M_FG0 0
F_FL3 1
F_FL2 0
F_FL1 1
F_FL0 0
Bit 7~4:
M_FG3~0 - MIR beginning Flag Number These bits define the number of transmitter Start Flag of MIR. Note that the number of MIR start flag should be equal or more than two which is defined in IrDA 1.1 physical layer. The default value is 2.
M_FG3~0
BEGINNING FLAG NUMBER
M_FG3~0
BEGINNING FLAG NUMBER
0000 0001 0010 0011 0100 0101 0110 0111 Bit 3~0:
Reserved 1 2 (Default) 3 4 5 6 8 F_FG3~0 - FIR Beginning Flag Number
1000 1001 1010 1011 1100 1101 1110 1111
10 12 16 20 24 28 32 Reserved
These bits define the number of transmitter Preamble Flag in FIR. Note that the number of FIR start flag should be equal to sixteen which is defined in IrDA 1.1 physical layer. The default value is 16.
- 81 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
M_FG3~0
BEGINNING FLAG NUMBER
M_FG3~0
BEGINNING FLAG NUMBER
0000 0001 0010 0011 0100 0101 0110 0111
Reserved 1 2 3 4 5 6 8
1000 1001 1010 1011 1100 1101 1110 1111
10 12 16 (Default) 20 24 28 32 Reserved
8.8.6
Set6.Reg5 - Winbond infrared ID Register 1
Winbond infrared ID1. Default value is 0x5C. Ready only.
Bit 7~0:
8.8.7
Set6.Reg6 - Winbond infrared ID Register 2
Winbond infrared ID2. Default value is 0XA3. Ready only.
Bit 7~0:
8.8.8
Bit 7-4: Bit 3-2:
Set6.Reg7 - High Speed infrared ID Select Register
Reserve. IRSEL0_IRRXH Pin Function select Bit 3-2 00 01 IRSEL0_IRRXH Pin function IRRXH FUNCTION IRSEL0 FUNCTION(Default value)
Bit 1-0:
Reserve.
- 82 -
W83L517D/W83L517D-F
8.9 Set7 - Remote control and IR module selection registers
REGISTER NAME REGISTER DESCRIPTION
ADDRESS OFFSET
0 1 2 3 4 5 6 7
RIR_RXC RIR_TXC RIR_CFG SSR IRM_SL1 IRM_SL2 IRM_SL3 IRM_CR
Remote Infrared Receiver Control Remote Infrared Transmitter Control Remote Infrared Config Register Sets Select Register Infrared Module (Front End) Select 1 Infrared Module Select 2 Infrared Module Select 3 Infrared Module Control Register
8.9.1
Set7.Reg0 - Remote Infrared Receiver Control (RIR_RXC)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
REG.
RIR_RXC
Default Value
RX_FR2 0
RX_FR1 0
RX_FR0 RX_FSL4 RX_FSL3 RX_FSL2 RX_FSL1 RX_FSL0 1 0 1 0 0 1
This register defines frequency range of receiver of remote IR. Bit 7~5: RX_FR2~0 - Receiver Frequency Range 2~0. These bits select the input frequency range of the receiver. It is implemented through a band pass filter, i.e., only the input signals whose frequency lies in the range defined in this register will be received. Bit 4~0: RX_FSL4~0 - Receiver Frequency Select 4~0. Selects the operation frequency of receiver.
- 83 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Table: Low Frequency range select of receiver. RX_FR2~0 (Low Frequency) 001 RX_FSL4~0 00010 00011 00100 00101 00110 00111 01000 01001 01011 01100 01101 01111 10000 10010 10011 10101 10111 11010 11011 11101 Min. 26.1 28.2 29.4 30.0 31.4 32.1 32.8 33.6* 34.4 36.2 37.2 38.2 40.3 41.5 42.8 44.1 45.5 48.7 50.4 54.3 Max. 29.6 32.0 33.3 34.0 35.6 36.4 37.2 38.1* 39.0 41.0 42.1 43.2 45.7 47.1 48.5 50.0 51.6 55.2 57.1 61.5 Min. 24.7 26.7 27.8 28.4 29.6 30.3 31.0 31.7 32.5 34.2 35.1 36.0 38.1 39.2 40.4 41.7 43.0 46.0 47.6 51.3 010 Max. 31.7 34.3 35.7 36.5 38.1 39.0 39.8 40.8 41.8 44.0 45.1 46.3 49.0 50.4 51.9 53.6 55.3 59.1 61.2 65.9 Min. 23.4 25.3 26.3 26.9 28.1 28.7 29.4 30.1 30.8 32.4 33.2 34.1 36.1 37.2 38.3 39.5 40.7 43.6 45.1 48.6 011 Max. 34.2 36.9 38.4 39.3 41.0 42.0 42.9 44.0 45.0 47.3 48.6 49.9 52n.7 54.3 56.0 57.7 59.6 63.7 65.9 71.0
Note that those unassigned combinations are reserved.
Table: High Frequency range select of receiver
RX_FR2~0 (HIGH FREQUENCY) 001
RX_FSL4~0 00011 01000 01011
Note that those unassigned combinations are reserved.
Min. 355.6 380.1 410.3
Max. 457.1 489.8 527.4
- 84 -
W83L517D/W83L517D-F
Table: SHARP ASK-IR receiver frequency range select. RX_FSL4~0 (SHARP ASK-IR) RX_FR2~0 001 010 011 100 101 110 480.0* 533.3* 457.1 564.7 436.4 600.0 417.4 640.0 400.0 685.6 384.0 738.5
Note that those unassigned combinations are reserved.
8.9.2
Set7.Reg1 - Remote Infrared Transmitter Control (RIR_TXC)
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Reg. RIR_TXC Default Value
TX_PW2 TX_PW1 TX_PW0 TX_FSL4 TX_FSL3 TX_FSL2 TX_FSL1 TX_FSL0 0 1 1 0 1 0 0 1
This Register defines the transmitter frequency and pulse width of remote IR. Bit 7~5: TX_PW2~0 - Transmitter Pulse Width 2~ 0. Select the transmission pulse width. TX_PW2~0 010 011 100 101
Note that those unassigned combinations are reserved.
Low Frequency 6 s 7 s 9 s 10.6 s
High Frequency 0.7 s 0.8 s 0.9 s 1.0 s
Bit 4~0:
TX_FSL4~0 - Transmitter Frequency Select 4~0.
Select the transmission frequency.
Table: Low frequency selected. TX_FSL4~0 00011 00100 ... 11101
Note that those unassigned combinations are reserved.
Low Frequency 30K Hz 31K HZ ... 56K Hz
- 85 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Table: High frequency selected. TX_FSL4~0 00011 01000 01011
Note that those unassigned combinations are reserved.
High Frequency 400K Hz 450K Hz 480K Hz
8.9.3
Set7.Reg2 - Remote Infrared Config Register (RIR_CFG)
Bit 7 P_PNB 0 Bit 6 SMP_M 0 Bit 5 RXCFS 0 Bit 4 0 Bit 3 TX_CFS 0 Bit 2 RX_DM 0 Bit 1 Bit 0
Reg. RIR_CFG Default Value Bit 7:
TX_MM1 TX_MM0 0 0
P_PNB: Programming Pulse Number Coding. Write a 1 to select programming pulse number coding. The code format is defined as follows.
(Number of bits) - 1
B7 B6
B5
B4 B3
B2
B1 B0
Bit value
If the bit value is set to 0, the high pulse will be transmitted/received. If the bit value is set to 1, then no energy will be transmitted/received. Bit 6: SMP_M - Sampling Mode. To select receiver sampling mode. When set to 0 then uses T-period sampling, that the T-period is programmed IR baud rate. When set to 1, programmed baud rate will be used to do oversampling. Bit 5: RXCFS - Receiver Carry Frequency Select RXCFS 0 1 Bit 4: Bit 3: Reserved, write 0. TX_CFS - Transmitter Carry Frequency Select. Select low speed or high speed transmitter carry frequency. Selected Frequency 30K ~ 56K Hz 400K ~ 480K Hz
- 86 -
W83L517D/W83L517D-F
TX_FCS 0 1 Bit 2: RX_DM - Receiver Demodulation Mode. RX_DM 0 1
Selected Frequency 30K ~ 56K Hz 400K ~ 480K Hz Demodulation Mode Enable internal decoder Disable internal decoder
Bit 1~0:
TX_MM1~0 - Transmitter Modulation Mode 1~0 TX_MM1~0 00 01 10 11 TX Modulation Mode Continuously send pulse for logic 0 8 pulses for logic 0 and no pulse for logic 1. 6 pulses for logic 0 and no pulse for logic 1 Reserved.
8.9.4
Set7.Reg3 - Sets Select Register (SSR)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
REG.
SSR
Default Value
Bit 7 1
Bit 6 1
Bit 5 1
Bit 4 1
Bit 3 0
Bit 2 1
Bit 1 0
Bit 0 0
Reading this register returns F4H. Select Register Set by writing a set number to this register.
8.9.5
Set7.Reg4 - Infrared Module (Front End) Select 1 (IRM_SL1)
Bit 7 0 Bit 6 0 Bit 5 0 Bit 4 0 Bit 3 0 Bit 2 0 Bit 1 0 Bit 0 0
Reg. IRM_SL1
Default Value
IR_MSP SIR_SL2 SIR_SL1 SIR_SL0
AIR_SL2 AIR_SL1 AIR_SL0
Bit 7:
IR_MSP - IR Mode Select Pulse When set to 1, the transmitter (IRTX) will send a 64 s pulse to setup a special IR frontend operational mode. When IR front-end module uses mode select pin (MD) and transmitter IR pulse (IRTX) to switch between high speed IR (such as FIR or MIR) and low speed IR (SIR or ASK-IR), this bit should be used.
Bit 6~4:
SIR_SL2~0 - SIR (Serial IR) mode select.
These bits are used to program the operational mode of the SIR front-end module. These values of SIR_SL2~0 will be automatically loaded to pins of IR_SL2~0, respectively, when (1) AM_FMT=1 (Automatic Format, in Set7.Reg7.Bit7); (2) the mode of Advanced IR is set to SIR (AD_MD2~0, in Set0.Reg4.Bit7~0).
- 87 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 3: Bit 2~0:
Reserved, write 0. AIR_SL2~0 - ASK-IR Mode Select.
These bits setup the operational mode of ASK-IR front-end module when AM_FMT=1 and AD_MD2~0 are configured to ASK-IR mode. These values will be automatically loaded to IR_SL2~0, respectively.
8.9.6
Set7.Reg5 - Infrared Module (Front End) Select 2 (IRM_SL2)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
REG.
IRM_SL2
Default Value
0
FIR_SL2 FIR_SL1 FIR_SL0 0 0 0
0
MIR_SL2 MIR_SL1 MIR_SL0 0 0 0
Bit 7: Bit 6~4:
Reserved, write 0. FIR_SL2~0 - FIR mode select.
These bits setup the operational mode of FIR front-end module when AM_FMT=1 and AD_MD2~0 are configured to FIR mode. These values will be automatically loaded to IR_SL2~0, respectively. Bit 3: Bit 2~0:
Reserved, write 0. MIR_SL2~0 - MIR Mode Select.
These bits setup the MIR operational mode when AM_FMT=1 and AD_MD2~0 are configured to MIR mode. These values will be automatically loaded to IR_SL2~0, respectively.
8.9.7
Set7.Reg6 - Infrared Module (Front End) Select 3 (IRM_SL3)
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
REG.
IRM_SL3
Default Value
0
LRC_SL2 LRC_SL1 LRC_SL0 0 0 0
0
HRC_SL2 HRC_SL1 HRC_SL0 0 0 0
Bit 7: Bit 6~4:
Reserved, write 0. LRC_SL2~0 - Low Speed Remote IR mode select.
These bits setup the operational mode of low speed remote IR front-end module when AM_FMT=1 and AD_MD2~0 are configured to Remote IR mode. These values will be automatically loaded to IR_SL2~0, respectively. Bit 3: Bit 2~0:
Reserved, write 0. HRC_SL2~0 - High Speed Remote IR Mode Select.
These bits setup the operational mode of high speed remote IR front-end module when AM_FMT=1 and .AD_MD2~0 are configured to Remote IR mode. These values will be automatically loaded to IR_SL2~0, respectively.
- 88 -
W83L517D/W83L517D-F
8.9.8 Set7.Reg7 - Infrared Module Control Register (IRM_CR)
BIT 7 BIT 6 BIT 5 IRSL0D 0 BIT 4 RXINV 0 BIT 3 TXINV 0 BIT 2 0 BIT 1 0 BIT 0 0
REG. IRM_CR
DEFAULT VALUE
AM_FMT IRX_MSL 0 0
Bit 7:
AM_FMT - Automatic Format
A write to 1 will enable automatic format IR front-end module. These bits will affect the output of IR_SL2~0 which is referred by IR front-end module selection (Set7.Reg4~6) Bit 6:
IRX_MSL - IR Receiver Module Select
Select the receiver input path from the IR front end module if IR module has a separated high speed and low speed receiver path. If the IR module has only one receiving path, then this bit should be set to 0.
IRX_MSL 0 1 Receiver Pin selected
IRRX (Low/High Speed) IRRXH (High Speed)
Bit 5:
IRSL0D - Direction of IRSL0 Pin
Select function for IRRXH or IRSL0 because they share common pin and have different input/output direction.
IRSL0_D 0 1 Function
IRRXH (I/P) IRSL0 (O/P) Table: IR receiver input pin selection
IRSL0D
IRX_MSL
AUX_RX
HIGH SPEED IR
SELECTED IR PIN
0 0 0 0 1 1 1 1
0 0 1 1 0 0 1 1
0 1 X X 0 1 X X
X X 0 1 X X 0 1
IRRX IRRXH IRRX IRRXH IRRX
Reserved
IRRX
Reserved
Note: that (1) AUX_RX is defined in Set5.Reg4.Bit4, (2) high speed IR includes MIR (1.152M or 0.576M bps) and FIR (4M bps), (3) IRRX is the input of the low speed or high speed IR receiver, IRRXH is the input of the high speed IR receiver.
- 89 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 4: Bit 3: Bit 2~0:
RXINV - Receiving Signal Invert
A write to 1 will Invert the receiving signal.
TXINV - Transmitting Signal Invert
A write to 1 will Invert the transmitting signal.
Reserved, write 0.
9. PARALLEL PORT
9.1 Printer Interface Logic
The parallel port of the W83L517D makes possible the attachment of various devices that accept eight bits of parallel data at standard TTL level. The W83L517D supports an IBM XT/AT compatible parallel port (SPP), bi-directional parallel port (BPP), Enhanced Parallel Port (EPP), Extended Capabilities Parallel Port (ECP), Extension FDD mode (EXTFDD), Extension 2FDD mode (EXT2FDD) on the parallel port. Refer to the configuration registers for more information on disabling, powerdown, and on selecting the mode of operation. Table 8-1 shows the pin definitions for different modes of the parallel port.
TABLE 8-1-1 PARALLEL PORT CONNECTOR AND PIN DEFINITIONS
HOST CONNECTOR
PIN NUMBER OF W83627HF
PIN ATTRIBUTE
SPP
EPP
ECP
1 2-9 10 11 12 13 14 15 16 17
Notes:
36 31-26, 24-23 22 21 19 18 35 34 33 32
O I/O I I I I O I O O
nSTB PD<0: 7> nACK BUSY PE SLCT nAFD nERR nINIT nSLIN
nWrite PD<0:7 > Intr nWait PE Select nDStrb nError nInit nAStrb
nSTB, HostClk2 PD<0:7> nACK, PeriphClk2 BUSY, PeriphAck2 PEerror, nAckReverse2 SLCT, Xflag2 nAFD, HostAck2 nFault1, nPeriphRequest2 nINIT1, nReverseRqst2 nSLIN1 , ECPMode2
n : Active Low 1. Compatible Mode 2. High Speed Mode 3. For more information, refer to the IEEE 1284 standard.
- 90 -
W83L517D/W83L517D-F
TABLE 8-1-2 PARALLEL PORT CONNECTOR AND PIN DEFINITIONS HOST CONNECTOR PIN NUMBER OF W83627HF PIN ATTRIBUTE SPP PIN ATTRIBUTE EXT2FDD PIN ATTRIBUTE EXTFDD
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
36 31 30 29 28 27 26 24 23 22 21 19 18 35 34 33 32
O I/O I/O I/O I/O I/O I/O I/O I/O I I I I O I O O
nSTB PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 nACK BUSY PE SLCT nAFD nERR nINIT nSLIN
--I I I I I --OD OD OD OD OD OD OD OD OD OD
--INDEX2# TRAK02# WP2# RDATA2# DSKCHG2# --MOA2# DSA2# DSB2# MOB2# WD2# WE2# RWC2# HEAD2# DIR2# STEP2#
--I I I I I ------OD OD OD OD OD OD OD OD
--INDEX2# TRAK02# WP2# RDATA2# DSKCHG2 # ------DSB2# MOB2# WD2# WE2# RWC2# HEAD2# DIR2# STEP2#
9.2
Enhanced Parallel Port (EPP)
TABLE 8-2 PRINTER MODE AND EPP REGISTER ADDRESS
A2 A1 A0 REGISTER NOTE
0 0 0 0 0 1 1 1 1
Notes:
0 0 1 1 1 0 0 1 1
0 1 0 0 1 0 1 0 1
Data port (R/W) Printer status buffer (Read) Printer control latch (Write) Printer control swapper (Read) EPP address port (R/W) EPP data port 0 (R/W) EPP data port 1 (R/W) EPP data port 2 (R/W) EPP data port 2 (R/W)
1 1 1 1 2 2 2 2 2
1. These registers are available in all modes. 2. These registers are available only in EPP mode.
- 91 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
9.2.1 Data Swapper
The system microprocessor can read the contents of the printer's data latch by reading the data swapper.
9.2.2
Printer Status Buffer
The system microprocessor can read the printer status by reading the address of the printer status buffer. The bit definitions are as follows:
7 6 5 4 3 2 1 1 1 TMOUT ERROR SLCT PE ACK BUSY 0
Bit 7: This signal is active during data entry, when the printer is off-line during printing, when the print head is changing position, or during an error state. When this signal is active, the printer is busy and cannot accept data. Bit 6: This bit represents the current state of the printer's ACK# signal. A 0 means the printer has received a character and is ready to accept another. Normally, this signal will be active for approximately 5 microseconds before BUSY# stops. Bit 5: Logical 1 means the printer has detected the end of paper. Bit 4: Logical 1 means the printer is selected. Bit 3: Logical 0 means the printer has encountered an error condition. Bit 1, 2: These two bits are not implemented and are logic one during a read of the status register. Bit 0: This bit is valid in EPP mode only. It indicates that a 10 S time-out has occurred on the EPP bus. A logic 0 means that no time-out error has occurred; a logic 1 means that a time-out error has been detected. Writing a logic 1 to this bit will clear the time-out status bit; writing a logic 0 has no effect.
9.2.3
Printer Control Latch and Printer Control Swapper
The system microprocessor can read the contents of the printer control latch by reading the printer control swapper. Bit definitions are as follows:
- 92 -
W83L517D/W83L517D-F
7 1
6 1
5
4
3
2
1
0
STROBE AUTO FD INIT SLCT IN IRQ ENABLE DIR
Bit 7, 6: These two bits are a logic one during a read. They can be written. Bit 5: Direction control bit When this bit is a logic 1, the parallel port is in input mode (read); when it is a logic 0, the parallel port is in output mode (write). This bit can be read and written. In SPP mode, this bit is invalid and fixed at zero. Bit 4: A 1 in this position allows an interrupt to occur when ACK# changes from low to high. Bit 3: A 1 in this bit position selects the printer. Bit 2: A 0 starts the printer (50 microsecond pulse, minimum). Bit 1: A 1 causes the printer to line-feed after a line is printed. Bit 0: A 0.5 microsecond minimum high active pulse clocks data into the printer. Valid data must be present for a minimum of 0.5 microseconds before and after the strobe pulse.
9.2.4
EPP Address Port
The address port is available only in EPP mode. Bit definitions are as follows:
7 6 5 4 3 2 1 0
PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7
The contents of DB0-DB7 are buffered (non-inverting) and output to ports PD0-PD7 during a write operation. The leading edge of IOW# causes an EPP address write cycle to be performed, and the trailing edge of IOW# latches the data for the duration of the EPP write cycle. PD0-PD7 ports are read during a read operation. The leading edge of IOR# causes an EPP address read cycle to be performed and the data to be output to the host CPU.
- 93 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
9.2.5 EPP Data Port 0-3
These four registers are available only in EPP mode. Bit definitions of each data port are as follows:
7 6 5 4 3 2 1 0
PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7
When accesses are made to any EPP data port, the contents of DB0-DB7 are buffered (non-inverting) and output to the ports PD0-PD7 during a write operation. The leading edge of IOW# causes an EPP data write cycle to be performed, and the trailing edge of IOW# latches the data for the duration of the EPP write cycle. During a read operation, ports PD0-PD7 are read, and the leading edge of IOR# causes an EPP read cycle to be performed and the data to be output to the host CPU.
9.2.6
Bit Map of Parallel Port and EPP Registers
7 PD7 BUSY# 1 1 PD7 PD7 PD7 PD7 PD7 6 PD6 ACK# 1 1 PD6 PD6 PD6 PD6 PD6 5 PD5 PE 1 DIR PD5 PD5 PD5 PD5 PD5 4 PD4 SLCT IRQEN IRQ PD4 PD4 PD4 PD4 PD4 3 PD3 2 PD2 1 INIT# INIT# PD2 PD2 PD2 PD2 PD2 1 PD1 1 AUTOFD# AUTOFD# PD1 PD1 PD1 PD1 PD1 0 PD0 TMOUT STROBE# STROBE# PD0 PD0 PD0 PD0 PD0
REGISTER
Data Port (R/W) Status (Read) Buffer
ERROF#
SLIN SLIN PD3 PD3 PD3 PD3 PD3
Control Swapper (Read) Control (Write) Latch
EPP Address Port R/W) EPP Data Port 0 (R/W) EPP Data Port 1 (R/W) EPP Data Port 2 (R/W) EPP Data Port 3 (R/W)
- 94 -
W83L517D/W83L517D-F
9.2.7 EPP Pin Descriptions
TYPE EPP DESCRIPTION
EPP NAME
nWrite PD<0:7> Intr nWait PE Select nDStrb nError NInits nAStrb
O I/O I I I I O I O O
Denotes an address or data read or write operation. Bi-directional EPP address and data bus. Used by peripheral device to interrupt the host. Inactive to acknowledge that data transfer is completed. Active to indicate that the device is ready for the next transfer. Paper end; same as SPP mode. Printer selected status; same as SPP mode. This signal is active low. It denotes a data read or write operation. Error; same as SPP mode. This signal is active low. When it is active, the EPP device is reset to its initial operating mode. This signal is active low. It denotes an address read or write operation.
9.2.8
EPP Operation
When the EPP mode is selected in the configuration register, the standard and bi-directional modes are also available. The PDx bus is in the standard or bi-directional mode when no EPP read, write, or address cycle is currently being executed. In this condition all output signals are set by the SPP Control Port and the direction is controlled by DIR of the Control Port. A watchdog timer is required to prevent system lockup. The timer indicates that more than 10 S have elapsed from the start of the EPP cycle to the time WAIT# is deasserted. The current EPP cycle is aborted when a time-out occurs. The time-out condition is indicated in Status bit 0.
9.2.8.1 EPP Operation
The EPP operates on a two-phase cycle. First, the host selects the register within the device for subsequent operations. Second, the host performs a series of read and/or write byte operations to the selected register. Four operations are supported on the EPP: Address Write, Data Write, Address Read, and Data Read. All operations on the EPP device are performed asynchronously.
9.2.8.2 EPP Version 1.9 Operation
The EPP read/write operation can be completed under the following conditions: a. If the nWait is active low, when the read cycle (nWrite inactive high, nDStrb/nAStrb active low) or write cycle (nWrite active low, nDStrb/nAStrb active low) starts, the read/write cycle proceeds normally and will be completed when nWait goes inactive high. b. If nWait is inactive high, the read/write cycle will not start. It must wait until nWait changes to active low, at which time it will start as described above.
9.2.8.3 EPP Version 1.7 Operation
The EPP read/write cycle can start without checking whether nWait is active or inactive. Once the read/write cycle starts, however, it will not terminate until nWait changes from active low to inactive high.
Publication Release Date: May 23, 2005 Revision 1.0
- 95 -
W83L517D/W83L517D-F
9.3 Extended Capabilities Parallel (ECP) Port
This port is software and hardware compatible with existing parallel ports, so it may be used as a
standard printer mode if ECP is not required. It provides an automatic high burst-bandwidth channel that supports DMA for ECP in both the forward (host to peripheral) and reverse (peripheral to host) directions. Small FIFOs are used in both forward and reverse directions to improve the maximum bandwidth requirement. The size of the FIFO is 16 bytes. The ECP port supports an automatic handshake for the standard parallel port to improve compatibility mode transfer speed. The ECP port supports run-length-encoded (RLE) decompression (required) in hardware. Compression is accomplished by counting identical bytes and transmitting an RLE byte that indicates how many times the next byte is to be repeated. Hardware support for compression is optional. For more information about the ECP Protocol, refer to the Extended Capabilities Port Protocol and ISA Interface Standard.
9.3.1
ECP Register and Mode Definitions
NAME ADDRESS I/O ECP MODES FUNCTION
data ecpAFifo dsr dcr cFifo ecpDFifo tFifo cnfgA cnfgB ecr
Base+000h Base+000h Base+001h Base+002h Base+400h Base+400h Base+400h Base+400h Base+401h Base+402h
R/W R/W R R/W R/W R/W R/W R R/W R/W
000-001 011 All All 010 011 110 111 111 All
Data Register ECP FIFO (Address) Status Register Control Register Parallel Port Data FIFO ECP FIFO (DATA) Test FIFO Configuration Register A Configuration Register B Extended Control Register
Note: The base addresses are specified by CR23, which are determined by configuration register or hardware setting.
MODE
DESCRIPTION
000 001 010 011 100 101 110 111
SPP mode PS/2 Parallel Port mode Parallel Port Data FIFO mode ECP Parallel Port mode EPP mode (If this option is enabled in the CR9 and CR0 to select ECP/EPP mode) Reserved Test mode Configuration mode
Note: The mode selection bits are bit 7-5 of the Extended Control Register.
- 96 -
W83L517D/W83L517D-F
9.3.2 Data and ecpAFifo Port
Modes 000 (SPP) and 001 (PS/2) (Data Port) During a write operation, the Data Register latches the contents of the data bus on the rising edge of the input. The contents of this register are output to the PD0-PD7 ports. During a read operation, ports PD0-PD7 are read and output to the host. The bit definitions are as follows:
7 6 5 4 3 2 1 0
PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7
Mode 011 (ECP FIFO-Address/RLE) A data byte written to this address is placed in the FIFO and tagged as an ECP Address/RLE. The hardware at the ECP port transmits this byte to the peripheral automatically. The operation of this register is defined only for the forward direction. The bit definitions are as follows:
7 6 5 4 3 2 1 0
Address or RLE
Address/RLE
9.3.3
Device Status Register (DSR)
These bits are at low level during a read of the Printer Status Register. The bits of this status register are defined as follows:
7 6 5 4 3 2 1 1 1 0 1
nFault Select PError nAck nBusy
- 97 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 7: This bit reflects the complement of the Busy input. Bit 6: This bit reflects the nAck input. Bit 5: This bit reflects the PError input. Bit 4: This bit reflects the Select input. Bit 3: This bit reflects the nFault input. Bit 2-0: These three bits are not implemented and are always logic one during a read.
9.3.4
Device Control Register (DCR)
The bit definitions are as follows:
7 1 6 1 strobe autofd nInit SelectIn ackIntEn Direction 5 4 3 2 1 0
Bit 6, 7: These two bits are logic one during a read and cannot be written. Bit 5: This bit has no effect and the direction is always out if mode = 000 or mode = 010. Direction is valid in all other modes. 0 1 the parallel port is in output mode. the parallel port is in input mode.
Bit 4: Interrupt request enable. When this bit is set to a high level, it may be used to enable interrupt requests from the parallel port to the CPU due to a low to high transition on the ACK# input. Bit 3: This bit is inverted and output to the SLIN# output. 0 1 The printer is not selected. The printer is selected.
Bit 2: This bit is output to the INIT# output. Bit 1: This bit is inverted and output to the AFD# output. Bit 0: This bit is inverted and output to the STB# output.
9.3.5
cFifo (Parallel Port Data FIFO) Mode = 010
This mode is defined only for the forward direction. The standard parallel port protocol is used by a hardware handshake to the peripheral to transmit bytes written or DMAed from the system to this FIFO. Transfers to the FIFO are byte aligned.
- 98 -
W83L517D/W83L517D-F
9.3.6 ecpDFifo (ECP Data FIFO) Mode = 011
When the direction bit is 0, bytes written or DMAed from the system to this FIFO are transmitted by a hardware handshake to the peripheral using the ECP parallel port protocol. Transfers to the FIFO are byte aligned. When the direction bit is 1, data bytes from the peripheral are read under automatic hardware handshake from ECP into this FIFO. Reads or DMAs from the FIFO will return bytes of ECP data to the system.
9.3.7
tFifo (Test FIFO Mode) Mode = 110
Data bytes may be read, written, or DMAed to or from the system to this FIFO in any direction. Data in the tFIFO will not be transmitted to the parallel port lines. However, data in the tFIFO may be displayed on the parallel port data lines.
9.3.8
cnfgA (Configuration Register A) Mode = 111
This register is a read-only register. When it is read, 10H is returned. This indicates to the system that this is an 8-bit implementation.
9.3.9
cnfgB (Configuration Register B) Mode = 111
The bit definitions are as follows:
7
6
5
4
3
2 1
1 1
0 1
IRQx 0 IRQx 1 IRQx 2 intrValue compress Bit 7: This bit is read-only. It is at low level during a read. This means that this chip does not support hardware RLE compression. Bit 6: Returns the value on the ISA IRQ line to determine possible conflicts.
- 99 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 5-3: Reflect the IRQ resource assigned for ECP port. cnfgB[5:3] 000 001 010 011 100 101 110 111 IRQ resource reflect other IRQ resources selected by PnP register (default) IRQ7 IRQ9 IRQ10 IRQ11 IRQ14 IRQ15 IRQ5
Bit 2-0: These five bits are at high level during a read and can be written.
9.3.10 ecr (Extended Control Register) Mode = all
This register controls the extended ECP parallel port functions. The bit definitions are follows:
7 6 5 4 3 2 1 0
empty full service Intr dmaEn nErrIntrEn MODE MODE MODE
Bit 7-5: These bits are read/write and select the mode. 000 001 Standard Parallel Port mode. The FIFO is reset in this mode. PS/2 Parallel Port mode. This is the same as 000 except that direction may be used to tri-state the data lines and reading the data register returns the value on the data lines and not the value in the data register. Parallel Port FIFO mode. This is the same as 000 except that bytes are written or DMAed to the FIFO. FIFO data are automatically transmitted using the standard parallel port protocol. This mode is useful only when direction is 0. ECP Parallel Port Mode. When the direction is 0 (forward direction), bytes placed into the ecpDFifo and bytes written to the ecpAFifo are placed in a single FIFO and auto transmitted to the peripheral using ECP Protocol. When the direction is 1 (reverse direction), bytes are moved from the ECP parallel port and packed into bytes in the ecpDFifo. Selects EPP Mode. In this mode, EPP is activated if the EPP mode is selected. Reserved.
010
011
100 101
- 100 -
W83L517D/W83L517D-F
Test Mode. The FIFO may be written and read in this mode, but the data will not be transmitted on the parallel port. Configuration Mode. The confgA and confgB registers are accessible at 0x400 and 0x401 in this mode.
110 111
Bit 4: Read/Write (Valid only in ECP Mode) 1 Disables the interrupt generated on the asserting edge of nFault. Enables an interrupt pulse on the high to low edge of nFault. If nFault is asserted 0 (interrupt) an interrupt will be generated and this bit is written from a 1 to 0. Bit 3: Read/Write 1 Enables DMA. 0 Disables DMA unconditionally. Bit 2: Read/Write 1 Disables DMA and all of the service interrupts. Enables one of the following cases of interrupts. When one of the service interrupts has occurred, the serviceIntr bit is set to a 1 by hardware. This bit must be reset to 0 to re-enable the interrupts. Writing a 1 to this bit will not cause an interrupt. (a) dmaEn = 1: During DMA this bit is set to a 1 when terminal count is reached. 0 (b) dmaEn = 0 direction = 0: This bit is set to 1 whenever there are writeIntr Threshold or more bytes free in the FIFO. (c) dmaEn = 0 direction = 1: This bit is set to 1 whenever there are readIntr Threshold or more valid bytes to be read from the FIFO. Bit 1: Read only 0 The FIFO has at least 1 free byte. 1 The FIFO cannot accept another byte or the FIFO is completely full. Bit 0: Read only 0 The FIFO contains at least 1 byte of data. 1 The FIFO is completely empty.
9.3.11 Bit Map of ECP Port Registers
D7 D6
PD6 nAck 1
D5
PD5 PError Directio
D4
PD4 Select ackIntEn
D3
PD3 nFault SelectIn
D2
PD2 1 nInit
D1
PD1 1 autofd
D0
PD0
NOTE
2
Data ecpAFifo Dsr Dcr CFifo ecpDFifo TFifo CnfgA CnfgB Ecr
PD7 Addr/RLE nBusy 1 ECP Data FIFO Test FIFO 0 compress
Address or RLE field 1 strobe
1 1 2 2 2
Parallel Port Data FIFO
0 intrValue MODE
0 1
1 1 nErrIntrEn
0 1 dmaEn
0 1 serviceIntr
0 1 full
0 1 empty
Notes: 1. These registers are available in all modes. 2. All FIFOs use one common 16-byte FIFO.
- 101 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
9.3.12 ECP Pin Descriptions
NAME TYPE DESCRIPTION
nStrobe (HostClk) PD<7:0> nAck (PeriphClk)
O I/O I
The nStrobe registers data or address into the slave on the asserting edge during write operations. This signal handshakes with Busy. These signals contains address or data or RLE data. This signal indicates valid data driven by the peripheral when asserted. This signal handshakes with nAutoFd in reverse. This signal deasserts to indicate that the peripheral can accept data. It indicates whether the data lines contain ECP command information or data in the reverse direction. When in reverse direction, normal data are transferred when Busy (PeriphAck) is high and an 8-bit command is transferred when it is low. This signal is used to acknowledge a change in the direction of the transfer (asserted = forward). The peripheral drives this signal low to acknowledge nReverseRequest. The host relies upon nAckReverse to determine when it is permitted to drive the data bus. Indicates printer on line. Requests a byte of data from the peripheral when it is asserted. This signal indicates whether the data lines contain ECP address or data in the forward direction. When in forward direction, normal data are transferred when nAutoFd (HostAck) is high and an 8-bit command is transferred when it is low. Generates an error interrupt when it is asserted. This signal is valid only in the forward direction. The peripheral is permitted (but not required) to drive this pin low to request a reverse transfer during ECP Mode. This signal sets the transfer direction (asserted = reverse, deasserted = forward). This pin is driven low to place the channel in the reverse direction. This signal is always deasserted in ECP mode.
Busy (PeriphAck)
I
PError (nAckReverse)
I
Select (Xflag)
I
nAutoFd (HostAck)
O
nFault (nPeriphRequest)
I
nInit (nReverseRequest) nSelectIn (ECPMode)
O O
9.3.13 ECP Operation
The host must negotiate on the parallel port to determine if the peripheral supports the ECP protocol before ECP operation. After negotiation, it is necessary to initialize some of the port bits. The following are required: (a) Set direction = 0, enabling the drivers. (b) Set strobe = 0, causing the nStrobe signal to default to the deasserted state. (c) Set autoFd = 0, causing the nAutoFd signal to default to the deasserted state. (d) Set mode = 011 (ECP Mode) ECP address/RLE bytes or data bytes may be sent automatically by writing the ecpAFifo or ecpDFifo, respectively.
- 102 -
W83L517D/W83L517D-F
9.3.13.1 Mode Switching
Software will execute P1284 negotiation and all operation prior to a data transfer phase under programmed I/O control (mode 000 or 001). Hardware provides an automatic control line handshake, moving data between the FIFO and the ECP port only in the data transfer phase (mode 011 or 010). If the port is in mode 000 or 001 it may switch to any other mode. If the port is not in mode 000 or 001 it can only be switched into mode 000 or 001. The direction can be changed only in mode 001. When in extended forward mode, the software should wait for the FIFO to be empty before switching back to mode 000 or 001. In ECP reverse mode the software waits for all the data to be read from the FIFO before changing back to mode 000 or 001.
9.3.13.2 Command/Data
ECP mode allows the transfer of normal 8-bit data or 8-bit commands. In the forward direction, normal data are transferred when HostAck is high and an 8-bit command is transferred when HostAck is low. The most significant bits of the command indicate whether it is a run-length count (for compression) or a channel address. In the reverse direction, normal data are transferred when PeriphAck is high and an 8-bit command is transferred when PeriphAck is low. The most significant bit of the command is always zero.
9.3.13.3 Data Compression
The W83627HF supports run length encoded (RLE) decompression in hardware and can transfer compressed data to a peripheral. Note that the odd (RLE) compression in hardware is not supported. In order to transfer data in ECP mode, the compression count is written to the ecpAFifo and the data byte is written to the ecpDFifo.
9.3.14 FIFO Operation
The FIFO threshold is set in configuration register 5. All data transfers to or from the parallel port can proceed in DMA or Programmed I/O (non-DMA) mode, as indicated by the selected mode. The FIFO is used by selecting the Parallel Port FIFO mode or ECP Parallel Port Mode. After a reset, the FIFO is disabled.
9.3.15 DMA Transfers
DMA transfers are always to or from the ecpDFifo, tFifo, or CFifo. The DMA uses the standard PC DMA services. The ECP requests DMA transfers from the host by activating the PDRQ pin. The DMA will empty or fill the FIFO using the appropriate direction and mode. When the terminal count in the DMA controller is reached, an interrupt is generated and serviceIntr is asserted, which will disable the DMA.
9.3.16 Programmed I/O (NON-DMA) Mode
The ECP or parallel port FIFOs can also be operated using interrupt driven programmed I/O. Programmed I/O transfers are to the ecpDFifo at 400H and ecpAFifo at 000H or from the ecpDFifo located at 400H, or to/from the tFifo at 400H. The host must set the direction, state, dmaEn = 0 and serviceIntr = 0 in the programmed I/O transfers. The ECP requests programmed I/O transfers from the host by activating the IRQ pin. The programmed I/O will empty or fill the FIFO using the appropriate direction and mode.
- 103 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
9.4 Extension FDD Mode (EXTFDD)
In this mode, the W83627HF changes the printer interface pins to FDC input/output pins, allowing the user to install a second floppy disk drive (FDD B) through the DB-25 printer connector. The pin assignments for the FDC input/output pins are shown in Table 6-1. After the printer interface is set to EXTFDD mode, the following occur: (1) Pins MOB# and DSB# will be forced to inactive state. (2) Pins DSKCHG#, RDATA#, WP#, TRAK0#, INDEX# will be logically ORed with pins PD4-PD0 to serve as input signals to the FDC. (3) Pins PD4-PD0 each will have an internal resistor of about 1K ohm to serve as pull-up resistor for FDD open drain/collector output. (4) If the parallel port is set to EXTFDD mode after the system has booted DOS or another operating system, a warm reset is needed to enable the system to recognize the extension floppy drive.
9.5
Extension 2FDD Mode (EXT2FDD)
In this mode, the W83627HF changes the printer interface pins to FDC input/output pins, allowing the user to install two external floppy disk drives through the DB-25 printer connector to replace internal floppy disk drives A and B. The pin assignments for the FDC input/output pins are shown in Table6-1. After the printer interface is set to EXTFDD mode, the following occur:
(1) Pins MOA#, DSA#, MOB#, and DSB# will be forced to inactive state. (2) Pins DSKCHG#, RDATA#, WP#, TRAK0#, and INDEX# will be logically ORed with pins PD4-PD0 to serve as input signals to the FDC. (3) Pins PD4-PD0 each will have an internal resistor of about 1K ohm to serve as pull-up resistor for FDD open drain/collector output. (4) If the parallel port is set to EXT2FDD mode after the system has booted DOS or another operating system, a warm reset is needed to enable the system to recognize the extension floppy drive.
10. GENERAL PURPOSE I/O
W83L517D provides 38 input/output ports that can be individually configured to perform a simple basic I/O function or a pre-defined alternate function. Those 38 GP I/O ports are divided into five groups, each group contains 6,8,8,8,8 ports from group 1 to group 5. The first group is configured through control registers in logical device 7, the second group in logical device 8,the third ,the fourth,and the fifth group in logical device 9. Users can configure each individual port to be an input or output port by programming respective bit in selection register (CRF0: 0 = output, 1 = input). Invert port value by setting inversion register (CRF2: 0 = non-inverse, 1 = inverse). Port value is read/written through data register (CRF1). Table 7.1 and 7.2 gives more details on GPIO's assignment. In addition, GPIO1 is designed to be functional even in power loss condition (VCC or VSB is off). Figure 7.1 shows the GP I/O port's structure. Right after Power-on reset, those ports default to perform basic input function except ports in GPIO1 which maintains its previous settings until a battery loss condition.
- 104 -
W83L517D/W83L517D-F
Table 9.1
SELECTION BIT 0 = OUTPUT 1 = INPUT INVERSION BIT 0 = NON INVERSE 1 = INVERSE BASIC I/O OPERATIONS
0 0 1 1
0 1 0 1 Table 9.2
Basic non-inverting output Basic inverting output Basic non-inverting input Basic inverting input
GP I/O PORT DATA REGISTER
REGISTER BIT ASSIGNMENT
GP I/O PORT
BIT 0 BIT 1 BIT 2 GP1 BIT 3 BIT 4 BIT 5 BIT 0 BIT 1 BIT 2 BIT 3 GP2 BIT 4 BIT 5 BIT 6 BIT 7 BIT 0 BIT 1 BIT 2 BIT 3
GP3
GP10 GP11 GP12 GP13 GP14 GP15 GP20 GP21 GP22 GP23 GP24 GP25 GP26 GP27 GP30 GP31 GP32 GP33 GP34 GP35 GP36 GP37
BIT 4 BIT 5 BIT 6 BIT 7
- 105 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Table 9.2, continued.
GP I/O PORT DATA REGISTER REGISTER BIT ASSIGNMENT
GP I/O PORT
BIT 0 BIT 1 BIT 2 BIT 3
GP4
GP40 GP41 GP42 GP43 GP44 GP45 GP46 GP47 GP50 GP51 GP52 GP53 GP54 GP55 GP56 GP57
BIT 4 BIT 5 BIT 6 BIT 7 BIT 0 BIT 1 BIT 2 BIT 3
GP5
BIT 4 BIT 5 BIT 6 BIT 7
Figure 7.1
- 106 -
W83L517D/W83L517D-F
11. ACPI REGISTERS FEATURES
W83L517D supports both ACPI and legacy power managements. The switch logic of the power management block generates an SMI interrupt in the legacy mode and an PME interrupt in the ACPI mode. The new ACPI feature routes SMI / PME logic output either to SMI or to PME .The
SMI / PME logic routes to SMI only when both PME_EN = 0 and SMIPME_OE = 1. Similarly, the SMI / PME logic routes to PME only when both PME_EN = 1 and SMIPME_OE = 1.
PME_EN IRQ events
SMIPME_OE
SMI / PME Logic
0 1
SMIPME_OE
SMI
PME
Device Idle Timers Device Trap Global STBY Timer
IRQs
Sleep/Wake State machine
WAK_STS Clock Control
12. CONFIGURATION REGISTER
12.1 Plug and Play Configuration
The W83L517D uses Compatible PNP protocol to access configuration registers for setting up different types of configurations. In W83L517D, there are eleven Logical Devices (from Logical Device 0 to Logical Device B with the exception of logical device 4 for backward compatibility) which correspond to eleven individual functions: FDC (logical device 0), PRT (logical device 1), UART1 (logical device 2), FIR (Fast IR, logical device 6), GPIO1 (logical device 7), GPIO2(logical device 8),GPIO3 ~GPIO5(logical device 9), and ACPI ((logical device A). Each Logical Device has its own configuration registers (above CR30). Host can access those registers by writing an appropriate logical device number into logical device select register at CR07.
- 107 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
12.2 Compatible PnP
12.2.1 Extended Function Registers
In Compatible PnP, there are two ways to enter Extended Function and read or write the configuration registers. HEFRAS (CR26 bit 6) can be used to select one out of these two methods of entering the Extended Function mode as follows:
HEFRAS ADDRESS AND VALUE
0 1
write 87h to the location 2Eh twice write 87h to the location 4Eh twice
After Power-on reset, the value on RTSA# (pin 49) is latched by HEFRAS of CR26. In Compatible PnP, a specific value (87h) must be written twice to the Extended Functions Enable Register (I/O port address 2Eh or 4Eh). Secondly, an index value (02h, 07h-FFh) must be written to the Extended Functions Index Register (I/O port address 2Eh or 4Eh same as Extended Functions Enable Register) to identify which configuration register is to be accessed. The designer can then access the desired configuration register through the Extended Functions Data Register (I/O port address 2Fh or 4Fh). After programming of the configuration register is finished, an additional value (AAh) should be written to EFERs to exit the Extended Function mode to prevent unintentional access to those configuration registers. The designer can also set bit 5 of CR26 (LOCKREG) to high to protect the configuration registers against accidental accesses. The configuration registers can be reset to their default or hardware settings only by a cold reset (pin MR = 1). A warm reset will not affect the configuration registers.
- 108 -
W83L517D/W83L517D-F
12.2.2 Extended Functions Enable Registers (EFERs)
After a power-on reset, the W83L517D enters the default operating mode. Before the W83L517D enters the extended function mode, a specific value must be programmed into the Extended Function Enable Register (EFER) so that the extended function register can be accessed. The Extended Function Enable Registers are write-only registers. On a PC/AT system, their port addresses are 2Eh or 4Eh (as described in previous section).
12.2.3 Extended Function Index Registers (EFIRs), Extended Function Data Registers(EFDRs)
After the extended function mode is entered, the Extended Function Index Register (EFIR) must be loaded with an index value (02h, 07h-FEh) to access Configuration Register 0 (CR0), Configuration Register 7 (CR07) to Configuration Register FE (CRFE), and so forth through the Extended Function Data Register (EFDR). The EFIRs are write-only registers with port address 2Eh or 4Eh (as described in section 12.2.1) on PC/AT systems; the EFDRs are read/write registers with port address 2Fh or 4Fh (as described in section 9.2.1) on PC/AT systems.
12.3 Configuration Sequence
To program W83L517D configuration registers, the following configuration sequence must be followed: (1). Enter the extended function mode (2). Configure the configuration registers (3). Exit the extended function mode
12.3.1 Enter the extended function mode
To place the chip into the extended function mode, two successive wrtites of 0x87 must be applied to Extended Function Enable Registers(EFERs, i.e. 2Eh or 4Eh).
12.3.2 Configurate the configuration registers
The chip selects the logical device and activates the desired logical devices through Extended Function Index Register(EFIR) and Extended Function Data Register(EFDR). EFIR is located at the same address as EFER, and EFDR is located at address (EFIR+1). First, write the Logical Device Number (i.e.,0x07) to the EFIR and then write the number of the desired logical device to the EFDR. If accessing the Chip(Global) Control Registers, this step is not required. Secondly, write the address of the desired configuration register within the logical device to the EFIR and then write (or read) the desired configuration register through EFDR.
12.3.3 Exit the extended function mode
To exit the extended function mode, one write of 0xAA to EFER is required. Once the chip exits the extended function mode, it is in the normal running mode and is ready to enter the configuration mode.
- 109 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
12.3.4 Software programming example
The following example is written in Intel 8086 assembly language. It assumes that the EFER is located at 2Eh, so EFIR is located at 2Eh and EFDR is located at 2Fh. If HEFRAS (CR26 bit 6) is set, 4Eh can be directly replaced by 4Eh and 2Fh replaced by 4Fh. ;----------------------------------------------------------------------------------; Enter the extended function mode ,interruptible double-write ;----------------------------------------------------------------------------------MOV OUT OUT DX,2EH DX,AL DX,AL MOV AL,87H |
;----------------------------------------------------------------------------; Configurate logical device 1, configuration register CRF0 | ;----------------------------------------------------------------------------MOV MOV OUT MOV MOV OUT ;MOV MOV OUT MOV OUT DX,2EH AL,07H DX,AL DX,2FH AL,01H DX,AL DX,2EH AL,F0H DX,AL DX,2FH DX,AL ; update CRF0 with value 3CH | ; select CRF0 ; select logical device 1 ; point to Logical Device Number Reg.
MOV AL,3CH ;-----------------------------------------; Exit extended function mode ;-----------------------------------------MOV OUT DX,2EH DX,AL MOV AL,AAH
- 110 -
W83L517D/W83L517D-F
12.4 Chip (Global) Control Register
CR02 (Default 0x00)
Bit 7 - 1: Reserved. Bit 0: SWRST --> Soft Reset.
CR07
The register is used to switch each logical device when write the number of logical device to EFDRs. Bit 7 - 0: LDNB7 - LDNB0 --> Logical Device Number Bit 7 - 0
CR20
Bit 7 - 0: DEVIDB7 - DEBIDB0 --> Device ID Bit 7 - Bit 0 = 0x 61 (read only).
CR21
Bit 7 - 0: DEVREVB7 - DEBREVB0 --> Device Rev = 0x 0X (read only). X : Version change number .(Bit 3~0).
CR22 (Default 0xff)
Bit 7~ 5: Reserved. Bit 4: Flash I/F Power down =0 =1 Power down No Power down
Bit 3: FIRPWD = 0 Power down = 1 No Power down Bit 2: URAPWD = 0 Power down = 1 No Power down Bit 1: PRTPWD = 0 Power down = 1 No Power down Bit 0: FDCPWD = 0 Power down = 1 No Power down
- 111 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
CR23 (Default 0x00)
Bit 7 ~ 1: Reserved. Bit 0: IPD (Immediate Power Down). When set to 1, it will put the whole chip into power down mode immediately.
CR24 (Default ss00,00ssb)
Bit 7 : Keyboard address decoder control = 0 Enable keyboard address (interface: KBCS# and MCCS#) decoder and IRQ1 , IRQ12 pass to SERIRQ. = 1 Disable keyboard interface. The corresponding power-on setting pin is PENKBC# (pin 52) Bit 6: CLKSEL(Enable 48Mhz) = 0 The clock input on Pin 1 should be 24 MHz. = 1 The clock input on Pin 1 should be 48 MHz. The corresponding power-on setting pin is PEN48 (pin 61). Bit[5:4]: ROM size select = 00 1Mb 01 2Mb 10 4Mb 11 Reserved Bit3:MEMW# Select (PIN97) = 0 MEMW# of flash interface is Disabled. = 1 MEMW# of flash interface is Enabled. Bit2: Reserved. Bit1 : Enable Flash ROM Interface = 0 Flash ROM Interface is enabled after hardware reset = 1 Flash ROM Interface is disabled after hardware reset This bit is read only, and set/reset by power-on setting pin. The corresponding power-on setting pin is PENROM#(pin 69) Bit 0: PNPCSV = 0 The Compatible PnP address select registers have default values. = 1 The Compatible PnP address select registers have no default value. The corresponding power-on setting pin is PNPCSV# (pin 43).
- 112 -
W83L517D/W83L517D-F
CR25 (Default 0x00)
Bit 7 ~ 4: Reserved Bit 3: FIRTRI When write to "1" ,FIR interface is set to tri-state and reduce the power consumption of chip. Bit 2: URATRI When write to "1", UART interface is set to tri-state and reduce the power consumption of chip. Bit 1: PRTTRI When write to "1", PRT interface is set to tri-state and reduce the power consumption of chip. Bit 0: FDCTRI. When write to "1",FDC interface is set to tri-state and reduce the power consumption of chip.
CR26 (Default 0s00,000b)
Bit 7: Reserved Bit 6: HEFRAS These two bits define how to enable Configuration mode. The corresponding power-on setting pin is RTSA# (pin 42). HEFRAS Address and Value = 0 Write 87h to the location 2E twice. = 1 Write 87h to the location 4Etwice. Bit 5: LOCKREG = 0 Enable R/W Configuration Registers. = 1 Disable R/W Configuration Registers. Bit 4: Reserved. Bit 3: DSFDLGRQ = 0 Enable FDC legacy mode on IRQ and DRQ selection, then DO register bit 3 is effective on selecting IRQ = 1 Disable FDC legacy mode on IRQ and DRQ selection, then DO register bit 3 is not effective on selecting IRQ Bit 2: DSPRLGRQ = 0 Enable PRT legacy mode on IRQ and DRQ selection, then DCR bit 4 is effective on selecting IRQ = 1 Disable PRT legacy mode on IRQ and DRQ selection, then DCR bit 4 is not effective on selecting IRQ Bit 1: DSUALGRQ = 0 Enable UART A legacy mode IRQ selecting, then MCR bit 3 is effective on selecting IRQ = 1 Disable UART A legacy mode IRQ selecting, then MCR bit 3 is not effective on selecting IRQ
- 113 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 0: DSUBLGRQ = 0 Enable UART B legacy mode IRQ selecting, then MCR bit 3 is effective on selecting IRQ = 1 Disable UART B legacy mode IRQ selecting, then MCR bit 3 is not effective on selecting IRQ
CR28 (Default 0000,0sssb)
Bit 7 : PRT_NFDD# = 0 Enable PRT_NFDD# Function.(Default) = 1 Disable PRT_NFDD# Function. Bit 6 - 3: Reserved. Bit 2 - 0: PRTMODS2 - PRTMODS0 = 0xx Parallel Port Mode = 100 Reserved = 101 External FDC Mode = 110 Reserved = 111 External two FDC Mode When bit 7 = 0 , the bit 2 is controlled by Pin PRT_NFDD#.
CR29 (GPIO10,GP11 Select default 0sss,s000b)
Bit 7: Reserved. Bit [6:5] : Pin 5 Func. Select = 00 GP11 = 01 WDTO = 10 RTCCS# = 11 IRQIN1 Bit[4:3] : Pin 4 Func. Select = 00 GP10 = 01 PLED = 10 P80CS# = 11 IRQIN0 Bit2~0: Reserved
CR2A (GPIO1 ~ 5& FlashROM Interface Selectd ,default 0x00)
Bit 7~5 : Reserved Bit 4 : (PIN 81 ~ 84 ,PIN 86 ~ 89 ) = 0 GPIO 5X = 1 Flash I/F (XA11 ~ XA18) Bit 3 : (PIN 73 ~80 ) = 0 GPIO 4X = 1 Flash I/F (XA3 ~ XA10)
- 114 -
W83L517D/W83L517D-F
Bit 2 : (PIN 57 ~ 59, PIN 61 ~ 64 , PIN 66) = 0 GPIO 3X = 1 Flash I/F (XD7 ~ XD0) Bit 1 : (PIN 71 ~72) = 0 GPIO 2X = 1 or CR24 bit7 =0 the Pin 71 ~ 72 is Flash I/F (XA1 ~ XA0) Bit 0: (PIN 67 ~ 70 ) = 0 GPIO1X = 1 Flash I/F( MEMR#, MEMW#, ROMCS#, XA0) This bits is set to 1 if Pin 45 is set to 0 during RESET Period.
CR2B (POWER DOWN CONTROL default s000,0000b)
Bit 7 : = 0 Normal operation = 1 Enable Power down mode (Active with bit[2..0] are all set to "1") Bit 6 -3 : Reserved Bit 2 : Enable Flash interface Power-down = 0 Normal operation = 1 Flash interface is in power-down mode if CR2B bit 7 =1 or PDCTL# = 0) Bit 1 : Enable SERIRQ interface Power-down = 0 Normal operation = 1 SERIRQ interface is in power-down mode if CR2B bit 7 =1 or PDCTL# = 0) Bit 0 : Enable FDC,UR, FIR ,PRT interface Power-down = 0 Normal operation = 1 FDC, UR, FIR, PRT interface is in power-down mode if CR2B bit 7 =1 or PDCTL# = 0
CR2C , CR2D , CR2E FOR WINBOND TEST Reserved. CR2C default 0x10
bit 7 - 5 : Reserved bit 4-0 : Fresh interface Cycle time control .
- 115 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
12.5 Logical Device 0 (FDC)
CR30 (Default 0x01 if PNPCSV = 0 during POR, default 0x00 otherwise)
Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive.
CR60, CR 61 (Default 0x03, 0xf0 if PNPCSV = 0 during POR, default 0x00, 0x00 otherwise)
These two registers select FDC I/O base address [0x100:0xFF8] on 8 byte boundary.
CR70 (Default 0x06 if PNPCSV = 0 during POR, default 0x00 otherwise)
Bit 7 - 4: Reserved. Bit 3 - 0: These bits select IRQ resource for FDC.
CR74 (Default 0x02 if PNPCSV = 0 during POR, default 0x04 otherwise)
Bit 7 - 3: Reserved. Bit 2 - 0: These bits select DRQ resource for FDC. = 0x00 DMA0 = 0x01 DMA1 = 0x02 DMA2 = 0x03 DMA3 = 0x04 - 0x07 No DMA active
CRF0 (Default 0x0E)
FDD Mode Register Bit 7: FIPURDWN This bit controls the internal pull-up resistors of the FDC input pins RDATA, INDEX, TRAK0, DSKCHG, and WP. =0 =1 Bit 6: INTVERTZ This bit determines the polarity of all FDD interface signals. =0 =1 FDD interface signals are active low. FDD interface signals are active high. The internal pull-up resistors of FDC are turned on.(Default) The internal pull-up resistors of FDC are turned off.
Bit 5: DRV2EN (PS2 mode only) When this bit is a logic 0, indicates a second drive is installed and is reflected in status register A.
- 116 -
W83L517D/W83L517D-F
Bit 4: Swap Drive 0, 1 Mode =0 =1 = 11 No Swap (Default) Drive and Motor select 0 and 1 are swapped. AT Mode (Default)
Bit 3 - 2 Interface Mode = 10 (Reserved) = 01 PS/2 = 00 Model 30 Bit 1: FDC DMA Mode = 0 Burst Mode is enabled = 1 Non-Burst Mode (Default) Bit 0: Floppy Mode = 0 Normal Floppy Mode (Default) = 1 Enhanced 3-mode FDD
CRF1 (Default 0x00)
Bit 7 - 6: Boot Floppy = 00 FDD A = 01 FDD B = 10 FDD C = 11 FDD D Bit 5, 4: Media ID1, Media ID0. These bits will be reflected on FDC's Tape Drive Register bit 7, 6. Bit 3 - 2: Density Select = 00 Normal (Default) = 01 Normal = 10 1 ( Forced to logic 1) = 11 0 ( Forced to logic 0) Bit 1: DISFDDWR = 0 Enable FDD write. = 1 Disable FDD write(forces pins WE, WD stay high). Bit 0: SWWP = 0 Normal, use WP to determine whether the FDD is write protected or not. = 1 FDD is always write-protected.
- 117 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
CRF2 (Default 0xFF)
Bit 7 - 6: FDD D Drive Type Bit 5 - 4: FDD C Drive Type Bit 3 - 2: FDD B Drive Type Bit 1 - 0: FDD A Drive Type
CRF4 (Default 0x00)
FDD0 Selection: Bit 7: Reserved. Bit 6: Precomp. Disable. = 1 Disable FDC Precompensation. = 0 Enable FDC Precompensation. Bit 5: Reserved. Bit 4 - 3: DRTS1, DRTS0: Data Rate Table select (Refer to TABLE A). = 00 Select Regular drives and 2.88 format = 01 3-mode drive = 10 2 Meg Tape = 11 Reserved Bit 2: Reserved. Bit 1:0: DTYPE0, DTYPE1: Drive Type select (Refer to TABLE B).
CRF5 (Default 0x00)
FDD1 Selection: Same as FDD0 of CRF4.
TABLE A
DRIVE RATE TABLE SELECT DRTS1 DRTS0 DATA RATE DRATE1 DRATE0 SELECTED DATA RATE MFM FM SELDEN
1 0 0 0 0 1 1 0 1 0 0 1 1 1 0 0 0 1
1 0 1 0 1 0 1 0 1 0 1 0
1Meg 500K 300K 250K 1Meg 500K 500K 250K 1Meg 500K 2Meg 250K
--250K 150K 125K --250K 250K 125K --250K --125K
1 1 0 0 1 1 0 0 1 1 0 0
- 118 -
W83L517D/W83L517D-F
TABLE B
DTYPE0 DTYPE1 DRVDEN0(PIN 2) DRVDEN1(PIN 3) DRIVE TYPE
4/2/1 MB 3.5"" 0 0 1 1 0 1 0 1 SELDEN DRATE1
SELDEN
DRATE0 DRATE0 DRATE0 DRATE1
2/1 MB 5.25" 2/1.6/1 MB 3.5" (3-MODE)
DRATE0
12.6 Logical Device 1 (Parallel Port)
CR30 (Default 0x01 if PNPCSV = 0 during POR, default 0x00 otherwise)
Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive.
CR60, CR 61 (Default 0x03, 0x78 if PNPCSV = 0 during POR, default 0x00, 0x00 otherwise)
These two registers select Parallel Port I/O base address. [0x100:0xFFC] on 4 byte boundary (EPP not supported) or [0x100:0xFF8] on 8 byte boundary (all modes supported, EPP is only available when the base address is on 8 byte boundary).
CR70 (Default 0x07 if PNPCSV = 0 during POR, default 0x00 otherwise)
Bit 7 - 4: Reserved. Bit [3:0]: These bits select IRQ resource for Parallel Port.
CR74 (Default 0x04)
Bit 7 - 3: Reserved. Bit 2 - 0: These bits select DRQ resource for Parallel Port. 0x00=DMA0 0x01=DMA1 0x02=DMA2 0x03=DMA3 0x04 - 0x07= No DMA active
- 119 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
CRF0 (Default 0x3F)
Bit 7: Reserved. Bit 6 - 3: ECP FIFO Threshold. Bit 2 - 0: Parallel Port Mode (CR28 PRTMODS2 = 0) = 100 Printer Mode (Default) = 000 Standard and Bi-direction (SPP) mode = 001 EPP - 1.9 and SPP mode = 101 EPP - 1.7 and SPP mode = 010 ECP mode = 011 ECP and EPP - 1.9 mode = 111 ECP and EPP - 1.7 mode.
12.7 Logical Device 2 (UART A)
CR30 (Default 0x01 if PNPCSV = 0 during POR, default 0x00 otherwise)
Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive.
CR60, CR 61 (Default 0x03, 0xF8 if PNPCSV = 0 during POR, default 0x00, 0x00 otherwise)
These two registers select Serial Port 1 I/O base address [0x100:0xFF8] on 8 byte boundary.
CR70 (Default 0x04 if PNPCSV = 0 during POR, default 0x00 otherwise)
Bit 7 - 4: Reserved. Bit 3 - 0: These bits select IRQ resource for Serial Port 1.
CRF0 (Default 0x00)
Bit 7 - 2: Reserved. Bit 1 - 0: SUACLKB1, SUACLKB0 = 00 = 01 = 10 = 11 UART A clock source is 1.8462 Mhz (24MHz/13) UART A clock source is 2 Mhz (24MHz/12) UART A clock source is 24 Mhz (24MHz/1) UART A clock source is 14.769 Mhz (24mhz/1.625)
- 120 -
W83L517D/W83L517D-F
12.8 Logical Device 6 (FIR)
CR30 (Default 0x00)
Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive.
CR60, CR 61 (Default 0x00, 0x00)
These two registers select IR I/O base address [0x100:0xFF8] on 8 byte boundary.
CR70 (Default 0x00)
Bit 7 - 4: Reserved. Bit [3:0]: These bits select IRQ resource for IR
CR74 (Default 0x04)
Bit 7-3 : Reserved. Bit 2-0 : These bits select DRQ resource for RX of FIR. = 0x00 DMA0 = 0x01 DMA1 = 0x02 DMA2 = 0x03 DMA3 = 0x04-0x07 No DMA active
CR75 (Default 0x04)
Bit 7-3 : Reserved. Bit 2-0 : These bits select DRQ resource for TX of FIR. = 0x00 DMA0 = 0x01 DMA1 = 0x02 DMA2 = 0x03 DMA3 = 0x04-0x07 No DMA active
CRF0 (Default 0x00)
Bit 7 - 4: Reserved. Bit 3: RXW4C =0 =1 No reception delay when SIR is changed from TX mode to RX mode. Reception delays 4 characters-time (40 bit-time) when SIR is changed from TX mode to RX mode.
- 121 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
Bit 2: TXW4C =0 =1 No transmission delay when SIR is changed from RX mode to TX mode. Transmission delays 4 characters-time (40 bit-time) when SIR is changed from RX mode to TX mode. No append hardware CRC value as data in FIR/MIR mode. Append hardware CRC value as data in FIR/MIR mode. Disable IR Bank selection. Enable IR Bank selection.
Bit 1 : APEDCRC =0 =1 =0 =1
Bit 0 : ENBNKSEL; Bank select enable
12.9
Logical Device 7 ( GPIO Port 1)
Bit 7 - 1: Reserved. Bit 0: = 1 GPIO1 port is Activate = 0 GPIO1 port is inactive.
CR30 ( Default 0x00)
CR62, CR 63 (Default 0x00, 0x00 )
These two registers select the GPIO1 base address [0x100:0xFFF] on 4byte boundary. IO address : CRF1 base address IO address + 1 : CRF3 base address IO address + 2 : CRF4 base address IO address + 3 : CRF5 base address
CR70 (Default 0x09 if PNPCSV = 0 during POR, default 0x00 otherwise when the port is active)
Bit [7:4]: These bits select IRQ resource for IRQIN1. Bit [3:0]: These bits select IRQ resource for IRQIN0.
CRF0 (GPIO1 selection register. Default 0xFF)
When set to a '1', respective GPIO port is programmed as an input port. When set to a '0', respective GPIO port is programmed as an output port.
CRF1 (GPIO1 data register. Default 0x00 when the port is active)
If a port is programmed to be an output port, then its respective bit can be read/written. If a port is programmed to be an input port, then its respective bit can only be read.
CRF2 (GP5 inversion register. Default 0x00 when the port is active)
When set to a '1', the incoming/outgoing port value is inverted. When set to a '0', the incoming/outgoing port value is the same as in data register.
- 122 -
W83L517D/W83L517D-F
CRF3 (PLED mode register. Default 0x00)
Bit 7 ~ 3 : Reserved . Bit 2: select WDTO count mode. =0 =1 = 00 = 01 = 10 = 11 second minute Power LED pin is tri-stated. Power LED pin is droved low. Power LED pin is a 1Hz toggle pulse with 50 duty cycle. Power LED pin is a 1/4Hz toggle pulse with 50 duty cycle.
Bit 1 ~ 0: select PLED mode
CRF4 (Default 0x00)
Watch Dog Timer Time-out value. Writing a non-zero value to this register causes the counter to load the value to Watch Dog Counter and start counting down. Reading this register returns current value in Watch Dog Counter instead of Watch Dog Timer Time-out value. Bit 7 - 0: = 0x00 Time-out Disable = 0x01 Time-out occurs after 1 second/minute = 0x02 Time-out occurs after 2 second/minutes = 0x03 Time-out occurs after 3 second/minutes ................................................ = 0xFF Time-out occurs after 255 second/minutes
CRF5 (Default 0x00)
Bit 7 ~ 6 : Reserved . Bit 5: Force Watch Dog Timer Time-out, Write only* = 1 Force Watch Dog Timer time-out event; this bit is self-clearing. Bit 4: Watch Dog Timer Status, R/W = 1 Watch Dog Timer time-out occurred. = 0 Watch Dog Timer counting Bit 3 -0: These bits select IRQ resource for Watch Dog. Setting of 2 selects SMI.
- 123 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
12.10 Logical Device 8 ( GPIO Port 2)
CR30 (Default 0x00)
Bit 7 - 1: Reserved. Bit 0: = 1 Activate GPIO2 = 0 GPIO2 is inactive.
CR62, CR 63 (Default 0x00, 0x00)
These two registers select the GPIO1 base address [0x100:0xFFF] on 1 byte boundary IO address : CRF1 base address
CRF0 (GP10-GP17 I/O selection register. Default 0xFF)
When set to a '1', respective GPIO port is programmed as an input port. When set to a '0', respective GPIO port is programmed as an output port.
CRF1 (GP10-GP17 data register. Default 0x00 when the port is active)
If a port is programmed to be an output port, then its respective bit can be read/written If a port is programmed to be an input port, then its respective bit can only be read
CRF2 (GP10-GP17 inversion register. Default 0x00 when the port is active)
When set to a '1', the incoming/outgoing port value is inverted. When set to a '0', the incoming/outgoing port value is the same as in data register.
12.11 Logical Device 9 (GPIO Port 3 ~ GPIO Port 5 )
CR30 (Default 0x00)
Bit 7 ~ 3: Reserved. Bit 2: = 1 Activate GPIO5. = 0 GPIO5 is inactive Bit 1: = 1 Activate GPIO4. = 0 GPIO4 is inactive Bit 0: = 1 Activate GPIO3. = 0 GPIO3 is inactive.
CR60,61(Default 0x00,0x00).
These two registers select the GP 3,4,5 base address(0x100:FFE) ON 3 bytes boundary. IO address : CRF1 base address IO address + 1 : CRF3 base address IO address + 2 : CRF7 base address
CRF0 (GP3 I/O selection register. Default 0xFF )
When set to a '1', respective GPIO port is programmed as an input port. When set to a '0', respective GPIO port is programmed as an output port.
- 124 -
W83L517D/W83L517D-F
CRF1 (GP3 data register. Default 0x00 when the port is active )
If a port is programmed to be an output port, then its respective bit can be read/written. If a port is programmed to be an input port, then its respective bit can only be read.
CRF2 (GP3 inversion register. Default 0x00 when the port is active)
When set to a '1', the incoming/outgoing port value is inverted. When set to a '0', the incoming/outgoing port value is the same as in data register.
CRF3 (GP4 I/O selection register. Default 0xFF )
When set to a '1', respective GPIO port is programmed as an input port. When set to a '0', respective GPIO port is programmed as an output port.
CRF4 (GP4 data register. Default 0x00 when the port is active)
If a port is programmed to be an output port, then its respective bit can be read/written. If a port is programmed to be an input port, then its respective bit can only be read.
CRF5 (GP4 inversion register. Default 0x00 when the port is active)
When set to a '1', the incoming/outgoing port value is inverted. When set to a '0', the incoming/outgoing port value is the same as in data register.
CRF6 (GP5 I/O selection register. Default 0xFF )
When set to a '1', respective GPIO port is programmed as an input port. When set to a '0', respective GPIO port is programmed as an output port.
CRF7 (GP5 data register. Default 0x00 when the port is active)
If a port is programmed to be an output port, then its respective bit can be read/written. If a port is programmed to be an input port, then its respective bit can only be read.
CRF8 (GP5 inversion register. Default 0x00 when the port is active)
When set to a '1', the incoming/outgoing port value is inverted. When set to a '0', the incoming/outgoing port value is the same as in data register.
12.12 Logical Device A (ACPI)
CR30 (Default 0x00)
Bit 7 - 1: Reserved. Bit 0: = 1 Activates the logical device. = 0 Logical device is inactive.
CR70 (Default 0x00)
Bit 7 - 4: Reserved. Bit 3 - 0: These bits select IRQ resources for S M I / PME
- 125 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
CRE0 (Default 0x00)
Bit7 : ENCIRWAKEUP. Enable CIR to wake-up system . = 0 Disable CIR wake up function = 1 Enable CIR wake up function
Bit 5 : CIR_STS. This bit is cleared by reading 1 this register.
= 0 Disable = 1 Enable
Bit6, 4 ~ 0 : Reserved CRE 1 (Default 0x00) CIR wake up index register
The range of CIR wake up index register is 0x20 ~ px2F .
CRE 2 CIR wake up data register
This register holds the value of wake up key register indicated by CRE1. This register can be read/written.
CRE5 (Default 0x00) Bit 7 : Reserved Bit 6 ~ 0 :Compared Code Length . When the compared codes are storage in the data register, these data length should be written to this register. CRE6 (Default 0x00)
Bit 7 - 6: Reserved. Bit 5 - 0: CIR Baud Rate Divisor. The clock base of CIR is 32khz, so that the baud rate is 32khz divided by ( CIR Baud Rate Divisor + 1).
CRE7 (Default 0x00)
Bit 7 - 3: Reserved.
Bit 2:Reset CIR Power-On function. After using CIR power-on, the software should write logical 1 to restart CIR power-on function.
Bit 1: Invert RX Data. = 1 Inverting RX Data. = 0 Not inverting RX Data. Bit 0: Enable Demodulation. = 1 Enable received signal to demodulate. = 0 Disable received signal to demodulate.
CRF0 (Default 0x00)
Bit 7: CHIPPME. Chip level auto power management enable. =0 =1 disable the auto power management functions enable the auto power management functions.
- 126 -
W83L517D/W83L517D-F
Bit 6: CIRPME. Consumer IR port auto power management enable. =0 =1 =0 =1 disable the auto power management functions enable the auto power management functions. disable the auto power management functions enable the auto power management functions.
Bit 5: MIDIPME. MIDI port auto power management enable.
Bit 4: Reserved. Return zero when read. Bit 3: PRTPME. Printer port auto power management enable. =0 =1 =0 =1 =0 =1 =0 =1
CRF1 (Default 0x00)
disable the auto power management functions. enable the auto power management functions. disable the auto power management functions. enable the auto power management functions. disable the auto power management functions. enable the auto power management functions. disable the auto power management functions. enable the auto power management functions.
Bit 2: FDCPME. FDC auto power management enable.
Bit 1: URAPME. UART A auto power management enable.
Bit 0: URBPME. UART B auto power management enable.
Bit 7: WAK_STS. This bit is set when the chip is in the sleeping state and an enabled resume event occurs. Upon setting this bit, the sleeping/working state machine will transition the system to the working state. This bit is only set by hardware and is cleared by writing a 1 to this bit position or by the sleeping/working state machine automatically when the global standby timer expires. =0 =1 the chip is in the sleeping state. the chip is in the working state.
Bit 6 - 5: Devices' trap status. Bit 4: Reserved. Return zero when read. Bit 3 - 0: Devices' trap status.
CRF3 (Default 0x00)
Bit 7 ~ 4: Reserved. Return zero when read. Bit 3 ~ 0: Device's IRQ status.
Publication Release Date: May 23, 2005 Revision 1.0
- 127 -
W83L517D/W83L517D-F
These bits indicate the IRQ status of the individual device respectively. The device's IRQ status bit is set by their source device and is cleared by writing a 1. Writing a 0 has no effect. Bit 3: PRTIRQSTS. printer port IRQ status. Bit 2: FDCIRQSTS. FDC IRQ status. Bit 1: URAIRQSTS. UART A IRQ status. Bit 0: URBIRQSTS. FIR IRQ status.
CRF4 (Default 0x00)
Bit 7 ~ 4: Reserved. Return zero when read. Bit 3 ~ 0: These bits indicate the IRQ status of the individual GPIO function or logical device respectively. The status bit is set by their source function or device and is cleared by writing a1. Writing a 0 has no effect. Bit 2: WDTIRQSTS. Watch dog timer IRQ status. Bit 1~0: Reserved
CRF9 (Default 0x00)
Bit 7 - 3: Reserved. Return zero when read. Bit 2: PME_EN: Select the power management events to be either an PME or SMI interrupt for the IRQ events. Note that: this bit is valid only when SMIPME_OE = 1. = 0 the power management events will generate an SMI event. = 1 the power management events will generate an PME event. Bit 1: FSLEEP: This bit selects the fast expiry time of individual devices. =0 1S = 1 8 mS. Bit 0: SMIPME_OE: This is the SMI and PME output enable bit. = 0 neither SMI nor PME will be generated. Only the IRQ status bit is set. = 1 an SMI or PME event will be generated.
13.
ORDERING INSTRUCTION
PART NO. PACKAGE REMARKS
W83L517D/W83L517D-F
100-pin LQFP
- 128 -
W83L517D/W83L517D-F
14. HOW TO READ THE TOP MARKING
Example: The top marking of W83L517D/W83L517D-F
inbond
W83L517D 20109620-91 014ABSA
1st line: Winbond logo
inbond
W83L517D-F
20109620-91
014ABSA
2nd line: the type number: W83L517D/W83L517D-F 3rd line: the tracking code 4th line: the tracking code 20109620-91 014 A B SA
20109620-91: wafer production series lot number 014: packages made in '2000, week 14 A: assembly house ID; A means ASE, S means SPIL.... etc. B: IC revision; A means version A, B means version B SA: for internal use
- 129 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
15. PACKAGE DIMENSIONS
HD D 75 76 51 50 A A2
A1
HE E
100 1 e b 25
26 L c L1
Y
Controlling Dimension : Millimeters
Symbol A A1 A2 b c D E e HD HE L L1 y 0 0.002 0.053 0.007 0.004 0.547 0.547 0.622 0.622 0.018 0.055 0.009 0.006 0.551 0.551 0.020 0.630 0.630 0.024 0.039 0.004 7 0 0.638 0.638 0.030 15.80 15.80 0.45 0.057 0.011 0.008 0.556 0.556 Dimension in inch Min Nom Max 0.063 Dimension in mm Min Nom Max 1.60 0.05 1.35 0.17 0.10 13.90 13.90 1.40 0.22 0.15 14.00 14.00 0.50 16.00 16.00 0.60 1.00 1.45 0.27 0.20 14.10 14.10 16.20 16.20 0.75 0.10 7
- 130 -
W83L517D/W83L517D-F
16. RECOMMENDED CIRCUIT
FLASH ROM
XD3 XD4 XD6 XD7 MEMR# MEMW# ROMCS# XA0 XA1 XA2 XA3 XA4 XA5 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 XD5 GND XD2 XD1 XD0 IOW# IOR# IRQ12IN IRQ1IN MCCS# KBCS# 3VCC U3
U1 XA18 XA17 XA16 XA15 XA14 XA13 XA12 XA11 XA10 XA9 XA8 XA7 XA6 XA5 XA4 XA3 XA2 XA1 XA0 1 30 2 3 29 28 4 25 23 26 27 5 6 7 8 9 10 11 12 31 24 22 NC/A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 WE# OE# CE# W29C020/40 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 13 14 15 17 18 19 20 21 XD0 XD1 XD2 XD3 XD4 XD5 XD6 XD7
COM PORT
5VCC 20 RTSA# DTRA# SOUTA RIA# CTSA# DSRA# SINA DCDA# 16 15 13 19 18 17 14 12 11 U2 VCC DA1 DA2 DA3 RY1 RY2 RY3 RY4 RY5 GND 14185 (SOP20) 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 P1 +12V DY1 DY2 DY3 RA1 RA2 RA3 RA4 RA9 -12V 1 5 6 8 2 3 4 7 9 10 NRTSA NDTRA NSOUTA NRIA NCTSA NDSRA NSINA -12VCC NDCDA 12VCC
XD[0..7]
XA[0..18]
5VCC 32 16
VCC MEMW# MEMR# ROMCS# GND
O.1U C1 XA6 XA7 XA8 XA9 XA10 XA11 XA12 XA13 XA14 GND XA15 XA16 XA17 XA18 5VCC HEAD# RDATA# WP# TRACK0# WE# WD# STEP# DIR# MOA# DSKCHG#
Note6: (Before updating the code of flash ROM,CR registers of W83L517D and chipset must be setted)
5VCC XA0 XA1 XA2 XA3 XA4 XA5 XA6 XA7 XA8 2 3 4 5 6 7 8 9 10 RP1 1 LAD0 LAD1 LAD2 LAD3 LFRAME# SERIRQ PDCTL# 2 3 4 5 6 7 8 9 10 RP2 3VCC 1
5VCC 8.2K RP3 1
76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
XA5/GP42 XA4/GP41 XA3/GP40 XA2/GP27 XA1/GP26 XA0/GP15 ROMCS#/GP14/PENROM# MEMW#/GP13 MEMR#/GP12 XD7/GP37 XD6/GP36 XD5/GP35 XD4/GP34 XD3/GP33 GND XD2/GP32 XD1/GP31 XD0/GP30 IOW#/GP25 IOR#/GP24 IRQ12IN/GP23 IRQ1IN/GP22 MCCS#/GP21 KBCS#/GP20/PENKB# VCC3V
XA6/GP43 XA7/GP44 XA8/GP45 XA9/GP46 XA10/GP47 XA11/GP50 XA12/GP51 XA13/GP52 XA14/GP53 GND XA15/GP54 XA16/GP55 XA17/GP56 XA18/GP57 VCC HEAD# RDATA# WP# TRACK0# WE# WD# STEP# DIR# MOA# DSKCHG#
IRSEL0 IRTX IRRX RIA# DCDA# SOUTA/PEN48 SINA DTRA#/PNPCSV# RTSA#/HEFRAS DSRA# VCC CTSA# STB# AFD# ERR# GND INIT# SLIN# PD7 PD6 PD5 PD4 PD3 PD2 PD1
IRSEL0 IRTX IRRX RIA# DCDA# SOUTA SINA DTRA# RTSA# DSRA# 5VCC CTSA# STB# AFD# ERR# GND INIT# SLIN# PD7 PD6 PD5 PD4 PD3 PD2 PD1
NRIA NDTRA NCTSA NSOUTA NRTSA NSINA NDSRA NDCDA
5 9 4 8 3 7 2 6 1
CONNECTOR DB9
FIR/SIR CON.
5VCC/3VCC JP1 IRSEL0 IRRX IRTX 1 2 3 4 5 HEADER 5
8.2K
8.2K XA18 XD0 XD1 XD2 XD3 XD4 XD5 XD6 XD7 2 3 4 5 6 7 8 9 10 RP4
R1 5VCC 1 IRQ1IN 8.2K R2 IRQ12IN 8.2K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
XA9 XA10 XA11 XA12 XA13 XA14 XA15 XA16 XA17
2 3 4 5 6 7 8 9 10
Note8:
DSA# INDEX# DRVDEN0 P80CS#/GP10 RTCCS#/GP11 CLKIN PME# LREST# PDCTL# GND SERIRQ PCICLK LDRQ# LAD0 VCC3V LAD1 LAD2 LAD3 LFRAME# PRT_NFDD# SLCT PE BUSY ACK# PD0
The resistor of SERIRQ is option if Host connected.
5VCC
W83L517D PD0 ACK# BUSY PE SLCT PRT_NFDD# LFRAME# LAD3 LAD2 LAD1 3VCC LAD0 LDRQ#
Note1: (P80CS# is decoded 80h and IOW#) (RTCCS# is decoded 70h and 71h) (CLKIN is 24 or 48MHz) (PDCTL# should connect a pull-high resistor)
8.2K 3VCC or 3VCC(stand by) R6
DSA# INDEX# DRVDEN0 P80CS# RTCCS# CLKIN PME# LREST# PDCTL# GND SERIRQ PCICLK
Note3: (PRT_NFDD# is used to detect external FDD)
Note2: (LDRQ# is connected to either one LDRQX of chipset)
4.7K Title Size B Date:
inbond
W83L517D LPC SUPER I/O Document Number L517_1 Tuesday, June 27, 2000 Sheet 1 of Rev 0.2
- 131 -
Publication Release Date: May 23, 2005 Revision 1.0
W83L517D/W83L517D-F
FDD_VCC CN1 PD0 PD7 PD4 AFD# PD6 INIT# PE SLCT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
F.D.D
5VCC
5VCC
R3 100K ROMCS# Q1 MOSFET P FDC_VCC KBCS# 1 2 1 1 JP2 2 5VCC JUMPER JP3 2 RP5
R4 100K 2 D1 DIODE 3 Q2 2 1
3
(PENROM#)
1 PRT_NFDD#
DTC144EUA RTSA#
(PENKB#)
1
JUMPER JP4 2
1 3 5 7
2 4 6 8
R5 100K
(HEFRAS#)
JUMPER JP5
4.7K
PD1 PD2 PD3 ERR#
DTRA#
1
2
(PNPCSV#) Note5: (The recommened circuit is used to controll power ON/OFF of External FDD). Note7:
JUMPER
(JP2[ON condition] during Power-On --> Disable BIOS ROM functions) (JP3[ON condition] during Power-On --> Disable K/B functions)
5VCC
(JP4[ON condition] during Power-On -->Configuration ports change to 4Eh (JP5[ON condition] during Power-On --> Disable all IO functions except K/B I/F)
D2 DIODE 2 1 1 D3 DIODE RP6 10P9R-2.7K 2 1
)
1
PRT PORT
2 3 4 5 6 7 8 9 10 STB# AFD# INIT# SLIN# PD[0..7] PD0 PD1 PD2 PD3 1 3 5 7 1 3 5 7 RPACK1 2 4 6 8
RP7 10P9R-2.7K
Note4: (For External FDD usd,set two of pin[18..25] that GND pin to be PRT_NFDD# and FDD_VCC)
1 14 2 15 3 16 4 17 5 18 6 19 7 20 8 21 9 22 10 23 11 24 12 25 13 J1
33 RPACK2 2 4 6 8
33 PD4 PD5 PD6 PD7 1 3 5 7 RPACK3 2 4 6 8
33 ERR# ACK# BUSY PE SLCT C2 180 C11 180 C3 180 C12 180 C4 180 C13 180 C5 180 C14 180 C6 180 C15 180 C7 180 C16 180 C8 180 C17 180 C9 180 C18 180 C10 180 Title Size B Date:
2 3 4 5 6 7 8 9 10
DB25
inbond
W83L517D LPC SUPER I/O Document Number L517_2 Tuesday, June 27, 2000 Sheet 2 of Rev 0.2
- 132 -
W83L517D/W83L517D-F
17. REVISION HISTORY
VERSION DATE PAGE DESCRIPTION
1.0
May 23, 2005
133
ADD Important Notice
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Further more, Winbond products are not intended for applications wherein failure of Winbond products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sales.
- 133 -
Publication Release Date: May 23, 2005 Revision 1.0

▲Up To Search▲

Price & Availability of W83L517DW83L517D-F

	To Download W83L517DW83L517D-F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .